SAFETY INSTRUCTIONS
m
IMPORTANT READ CAREFULLY: It is important that all operators read and understand all
sections of this Tool Technical Data manual and the separate Safety and Operating Instruction
Manual which come with this tool. Failure to do so could result in you or others in the working
area to be seriously injured.
m
WARNING!
Eye protection in accordance with 89/686/EEC, and with equal or greater grade than defined
in EN166 should be used. However all aspects of operators work, environment and other type/s of machinery
being used, should also be considered when selecting any personal protection equipment. Note: Non-side
shielded spectacles and face shields alone do not provide adequate protection.
m
WARNING! To prevent accidental injuries:
• Never place a hand or any other part of the body in fastener discharge area of tool.
• Never point tool at yourself or anyone whether it contains fasteners or not.
• Never engage in horseplay.
• Never pull the trigger unless the nose is directed towards the work.
• Always handle the tool with care.
•
This tool is intended to be used for fastening wood to wood in pallet/crate and construction applications.
DO NOT USE for fastening harder materials which could cause buckling of the fasteners and damage to the
tool. If you are unsure of the suitability of this tool for certain applications, please contact your local sales
office.
• Do not pull the trigger or depress the work safety yoke whilst loading the tool.
• To prevent accidental actuation and possible injury, always disconnect air supply:
1. Before making adjustments. 2. When servicing the tool. 3. When clearing a jam. 4. When tool is not in use.
5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.
• Read the additional Safety & Operating instructions booklet before using tool.
• Do not use oxygen and combustible gases as an energy source for pneumatically operated tools.
• The operation of this tool can cause sparks and act as a source of ignition for flammable fuels and gases.
LOADING THE TOOL
m
Warning!
When loading the tool 1) Never place a hand or any part of the body in fastener discharge area of
the tool; 2) Never point the tool at self or anyone else; 3) Do not pull the trigger or depress the safety yoke as
accidental actuation may occur, possibly causing injury.
1. Open the magazine: Pull down on the latch and swing the door open.
Swing magazine cover open. (Fig 1)
2. Check adjustment: the nailer must be set for the length of nail to be used.
Nails will not feed smoothly if the magazine is not correctly adjusted.
To change the setting: (Figs 2a - 2c)
a) Release the canister latch on the rear of the canister.
b) Pull out the canister bottom by swinging right to left until tabs disengage.
c) Inside the canister bracket there are settings in inches and millimeters. The canister is adjusted correctly
when the length of fastener being used is shown in the window of the canister bottom.
d) Push back the canister bottom and engage the latch.
3. Load the coil of nails: (Fig 3)
Place a coil of nails over the post in the canister.
Uncoil enough nails to reach the feeder pawl and place the second nail between the teeth of the feeder pawl.
The nail heads fit in slot on the feeder pawl.
GB
© Bostitch
GB
Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR
Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne
signifient en rien que les produits soient conformes aux normes CE.
DE
Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments
erfüllen nicht die CE-Richtlinien für Produkte.
NL
Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document
willen niet zeggen dat de producten voldoen aan de CE-vereisten.
DK
Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse
for produkterne.
FI
Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille
CE-yhdenmukaisuutta.
GR
Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT
Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non
garantiscono la conformità CE per i relativi prodotti.
NO
Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke
kravene for CE-merking for produktet.
PT
Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão
em conformidade com a CE para os produtos.
ES
Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE
Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL
Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego
dokumentu nie stanowią deklaracji zgodności CE prezentowanych produktów.
CZ
Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego
dokumentu nie stanowią deklaracji zgodności CE prezentowanych produktów.
SK
Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE
pre dané výrobky.
HU
A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum
nem jelenti a termék CE-megfelelőségét.
RO
Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
