ITEM
PART NO.
DESCRIPTION
NO.
47.
LW10
#10 Lock Washer
48.
UP2912.3
3/32 x 3/4” Cotter Pin
49.
D14164
Pusher Spring
50.
UB2814.2
Pin, Spring .094 x .88
51.
D60054
Spring, Valve
ITEM
PART NO.
DESCRIPTION
NO.
52.
D60009
Valve Stem
53.
851201
O-Ring .301 x .070
54.
D60008
Valve Body
55.
86458
O-Ring 1/16”x 1/2” ID
56.
86998
O-Ring 1/16”x 9/16” ID
57.
86459
O-Ring 1/16”x 5/8” ID
VARIABLE PARTS
ITEM NO.
DESCRIPTION
STANDARD PARTS
OPTIONAL PARTS
11.
Driver
D16170 (long)
D16178 (short)
30.
Clincher
D16124 (deep)
D16124B (deep pointed)
D14135 (shallow)
33.
C’ Balance Hanger
D16106A
29.
Magazine Assembly
D16169A
D16164A
[5/8” (15.9mm)
[7/16” (11.1mm)
3/4” (19.1mm)
5/8” (15.9mm)
and 7/8” (22.2mm)
and 3/4” (19.1mm)
staples]
staples]
D14135 clinchers are for shallow penetration as in single
wall board and will clinch inside board without damage to
contents. D16124 clinchers are for deep penetration as in
double wall board.
CAUTION: WHEN USING DEEP PENETRATION
CLINCHERS, IT MAY BE NECESSARY TO USE A
FILLER TO PREVENT DAMAGE TO
MERCHANDISE. D16124 CLINCHERS MAY ALSO
BE USED FOR STAPLING THROUGH SINGLE
WALL BOARD PROVIDED A FILLER IS USED TO
PREVENT DAMAGE TO CONTENTS OR
CLINCHERS.
To obtain maximum efficiency from the staple
closure, it is important that the staple be clinched properly.
Proper clinching for any thickness board may be obtained by
adjusting the clincher setting with staples of proper leg length.
Use the proper length staples for the thickness of work to be
stapled, otherwise unnecessary pressure is exerted and
staple crowns and legs will be distorted, or the clinch will be
too loose.
CLINCHER ADJUSTMENT:
Clincher adjustment for depth of penetration is obtained by
loosening the clincher adjusting clamp screw on front of
machine and moving it up or down. When in its highest
position, the clinchers are set for the shallowest staple
penetration. Lowering the clinchers increases the
penetration. After establishing the setting, tighten
adjustment screw.
NOTE: The D16-2AD is equipped with a driver to
countersink the crown of the staple below the surface of
the box. The shorter driver, available on order, will allow the
crown of the staple to rest on the top of the box.
Staple driven completely through two
thicknesses of corrugated board and clinched on
underside.
Staple clinched “blind” when desired, in two
thicknesses of corrugated board.
D14135 CLINCHERS
Approx. Clincher Adjusting
Clamp Setting
6
5
4
3
2
1
5/8”
(2) A Board-Blind
(15.9mm)
Leg
3/4”
(2) A Board-Through
(19.1mm)
Leg
7/16”
(2) B Board-Blind
(11.1mm)
Leg
5/8”
(2) B Board-Through
(15.9mm)
Leg
7/16”
(2) C Board-Blind
(11.1mm)
Leg
5/8”
(2) C Board-Through
(15.9mm)
Leg
D16124 DEEP CLINCHERS
Approx. Clincher Adjusting
Clamp Setting
6
5
4
3
2
1
3/4”
(2) A Board-Through
(19.1mm)
Leg
3/4”
(2) AB Board-Blind
(19.1mm)
Leg
7/8”
(2) AB Board-Through
(22.2mm)
Leg
Always disconnect air supply: 1.)
Before making adjustments; 2.)
When servicing the tool; 3.) When
clearing a jam; 4.) When tool is not
in use; 5.) When moving to a
different work area, as accidental
actuation may occur, possibly
causing injury.
When working on air tools note the
warnings in this manual and use
extra care when evaluating problem tools.
