Bostitch BTFP12570 Operation And Maintenance Manual Download Page 3

DEFINITIONS - SAFETY GUIDELINES

When using any pneumatic tool, all safety precautions , as outlined below, should be followed to avoid the 

risk of death or serious injury. Read and understand the instructions before operating the tool.

This manual contains information that is important for you to know and understand. 

This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT 

PROBLEMS. To help you recognize this information, we use the symbols below. Please read 

the manual and pay attention to these symbols.
Indicates an imminently hazardous situation which, if not avoided, will result in death or 

serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or 

serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or 

moderate injury.

Indicates a situation which, if not avoided, may result in property damage.

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI specifications and provides protection against 

flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator 

and others in the work area when connecting to air supply, loading, operating or servicing 

this tool. Eye protection is required to guard against flying fasteners and debris, which 

could cause severe eye injury.
The employer and/or user must ensure that proper eye protection is worn. Eye protection 

equipment must conform to the requirements of the American National Standards 

Institute, ANSI CAN/CSA Z94.3 and provide both frontal and side protection. NOTE: Non-

side shielded spectacles and face shields alone do not provide adequate protection.
Additional Safety Protection will be required in some environments. For example, the 

working area may include exposure to noise level which can lead to hearing damage. The 

employer and user must ensure that any necessary hearing protection is provided and 

used by the operator and others in the work area. Some environments will require the use 

of head protection equipment. When required, the employer and user must ensure that 

head protection conforming to ANSI CAN/CSA Z89.1 is used.

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as 

tool may explode, possibly causing injury.
Do not use supply sources which can potentially exceed 200 P.S.I.G. (14kg/cm

2

 ) as tool 

may burst, possibly causing injury.
The connector on the tool must not hold pressure when air supply is disconnected. If a 

wrong fitting is used, the tool can remain charged with air after disconnecting and thus 

will be able to drive a fastener even after the air line is disconnected possibly causing 

injury.
Do not pull trigger or depress contact arm while connected to the air supply as the tool 

may cycle, possibly causing injury.
Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 

3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work 

area, as accidental actuation may   occur, possibly causing injury.

LOADING TOOL

When loading tool: 1.) Never place a hand or any part of body in fastener discharge area 

of tool; 2.) Never point tool at anyone; 3.) Do not pull the trigger or depress the trip as 

accidental actuation may occur, possibly causing injury.

OPERATION

Always handle the tool with care: 1.) Never engage in horseplay; 2.) Never pull the trigger 

unless nose is directed toward the work; 3.) Keep others a safe distance from the tool while 

tool is in operation as accidental actuation may occur, possibly causing injury.
The operator must not hold the trigger pulled on contact arm tools except during fastening 

operation as serious injury could result if the trip accidentally contacted someone or 

something, causing the tool to cycle.

-3-

Summary of Contents for BTFP12570





























Reviews: