background image

12

Set Air pressure to 60-80 PSI,  

410-550 KPA or 041-0.55 MPA

Make sure air compressor is turned on and 

capable of 7-8 CFM (cubic feet per minute) 

free air delivery, or 200 LPM (litres per minute)

5

8

9

10

6

Depress switch and the pilot arc fires from  

the nozzle and care must be taken when  

depressing trigger switch. This arc is designed 

to burn through contamination, paint or rust 

to allow the main cutting arc to connect with 

bare metal. Continued depressing of the switch 

away from cutting surface will reduce the 

effectiveness of the consumables and greatly 

reduce their life span.

 

Switch ON the machine using Mains Power 

Switch.  

Set the RUN / SET switch to SET and test the 

Air Pressure by sliding the safety switch back 

on the torch and depress torch trigger 

The plasma torch trigger switch has a safety 

trigger to prevent accidental triggering of the 

pilot arc. Slide the safety switch back and 

depress switch.

Select your required current turning the 

Current Adjustment Knob. If the plasma is 

struggling to penetrate, increase amperage by 

turning the Current Adjustment Knob  

Set the RUN / SET switch to RUN,

7

SET UP P40 Inverter DC Plasma Cutter- continued

Summary of Contents for P40





















Reviews: