Boss Snowrator MAG Owner'S Manual Download Page 6 | Manualshive

Page: 6 / 16

background image

Routing the Hydraulic Hoses

1.

Shut off the machine engine, wait for all moving parts to stop, ensure that the parking brake is engaged,
and remove the key.

2.

Route the hydraulic hoses.

Note:

When changing attachments on the machine you may need to relieve stored hydraulic pressure by

slightly loosening hydraulic lines on the snow thrower or wiggle the joysticks on machine.

g383236

Figure 6

6

«
...
4
5
6
7
8
...
»

Summary of Contents for Snowrator MAG

















Reviews:

No comments

Related manuals for Snowrator MAG

Brand: Tanaka Pages: 86

Brand: Kärcher Pages: 8

Brand: Tanaka Pages: 32

Brand: Mantis Pages: 10

Brand: MSW Pages: 11

Groundsmaster 7200 Series

Brand: Toro Pages: 72

Brand: Worcraft Pages: 59

33.BY.001 BYTE 461 C

Brand: RCm Pages: 94

Brand: RCm Pages: 203

Brand: HENX Pages: 16

Brand: Poulan Pro Pages: 11

Brand: Power smart Pages: 19

Brand: Cub Cadet Pages: 16

Brand: Grizzly Pages: 148

Brand: Tennant Pages: 22

Brand: Eurotops Pages: 20

Brand: Yard-Man Pages: 28

Brand: Yardworks Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands