Boss Snowrator MAG Owner'S Manual Download Page 16

Page: 16 / 16

Troubleshooting

Problem

Possible Cause

Corrective Action

1. The chain broke.

1. Check the chain for break. Replace

any damaged components.

2. The auger could be jammed.

2. Check the auger for debris.

3. The auger bolts are bad.

3. Inspect the auger bolts. Replace any

damaged components.

The auger is not moving but the impeller
still rotates.

4. A sprocket key could be missing or

bad.

4. Inspect the sprocket keys. Replace

any damaged components.

The impeller is not moving but the auger
still rotates.

1. Debris is caught in the blades.

1. Check the impeller for debris.

1. The hydraulic fluid level is low.

1. Check the hydraulic fluid level; refer to

your Snowrator MAG Owner's Manual.

2. The hydraulic fluid level is low and the

Snowrator MAG was stopped quickly.

2. Slow the Snowrator MAG gradually

before coming to a stop when the
hydraulic fluid is low.

3. The pressure relief valve is bad

3. Check the pressure relief valve,

located on the Snowrator MAG traction
unit. If the valve is contaminated, clear
or replace it.

4. A cylinder or hose is bad.

4. Check the cylinders, hoses, and all

fittings for leaks. Tighten any loose
connections. Replace any damaged
components.

The attachment is not functioning or they
move slowly.

5. The hydraulic couplings are not

attached to the vehicle.

5. Connect the attachment hydraulics to

the vehicle hydraulics.

1. There is pressure build up in the

snowthower circuits.

1. Loosen the hydraulic lines on the

snowthrower to relieve the pressure.

The hydraulic connections does not
connect or they are hard to connect.

2. There is pressure build up in the

Snowrator MAG valves.

2. Wiggle the joysticks on the MAG to

relieve the pressure.

1. A hose is bad.

1. Check hoses for leaks. Tighten any

loose connections. Replace any
damaged components.

2. A cylinder is bad.

2. Replace the cylinder.

Oil leaks from the hydraulic cylinders.

3. The cylinder rod is pitted.

3. Polish the rod with steel wool. Replace

the cylinder if the pitting is too bad.

The attachment does not follow the
contour of the ground.

1. The attachment coupler lever is not in

the float position.

1. Ensure that the attachment coupler

lever is in the float position.

Summary of Contents for Snowrator MAG

















Search results

Summary of Contents for Snowrator MAG

Reviews:

Related manuals for Snowrator MAG

Brands by name

Popular brands

Boss Snowrator MAG, Owner'S Manual

Search results

Summary of Contents for Snowrator MAG

Reviews:

Related manuals for Snowrator MAG

Brands by name

Popular brands