background image

24

en | TroubleShooting Guide

High Performance LCD Monitors

F.01U.075.713 | 1.0 | 2008.03

User’s Manual

Bosch Security Systems, Inc.

9

TroubleShooting Guide

Problem

Solution

No image is displayed on 

screen

Check that the power cord of the monitor is securely 

connected into the wall outlet or grounded extension cable or 

strip.

Power switch should be in the ON position and the LED lit.

Check that the Brightness and/or Contrast adjustments of the 

display have not been turned down to minimum levels.

“Going to Sleep” 

message is displayed

The signal cable should be completely connected to the video 

card/computer.

The video card should be completely seated in its slot and the 

computer switched ON.

Display image is not 

centered, is too small, or 

too large in the 

PC

 mode

Push the down key to activate the Autoset function.

-or-

Adjust the Clock and Phase in the PC OSD submenu.

Vertical or horizontal 

noise is present in the 

picture

Push the down key to activate the Autoset function (for VGA inputs 

only).

-or-

Adjust the Clock and Phase in the PC OSD submenu.

Incorrect colors

Press the 

Menu

 button on the front panel of the monitor, then 

press the down arrow to select the 

Color Tone 

menu. Press 

the down arrow on the front panel and select Cool, Warm, or 

Normal.

- or -

Press the 

Menu

 button on the front panel of the monitor, then 

press the right arrow to select the 

Setup

 menu. Press the 

down arrow on the front panel and select Recall to reset to 

the default settings.

The error message “Out 

of Range” is displayed

PC is operating with either a resolution or timing mode that is not 

supported by the monitor. Change the PC timing mode to one of 

the valid combinations below:

640 x 480; 60/72/75 Hz

800 x 600; 60/72/75 Hz

1024 x 768; 60/70/75 Hz

1280 x 1024; 60 Hz

1600 x 1200; 60 Hz

Summary of Contents for UML-172-90





































Reviews: