background image

Commissioning

 

TSS – 6720887693 (2018/10)

22

10

Commissioning

NOTICE: 

Collector damage from evaporation in the solar circuit or frozen 
water!

▶ Only flush and fill the solar thermal system when the sun is not 

shining on the collectors and no frost (if purging with water) is 
expected.

▶ Carry out tightness test. Observe the permitted pressures for all 

assemblies. 

Fig. 58   Check all connections for leakage

10.1

Lightning protection and equipotential bonding

Necessity of lightning protection

▶ Check regional regulations as to whether a lightning protection 

system is required. 

The lightning conductor is often required in the following cases: 

• Building height of over 20 m
• Buildings that are significantly taller than surrounding buildings
• Buildings considered in need of high protection 

(e.g. schools, hospitals and high-rise buildings)

Equipotential bonding for the thermal solar system

If a lightning protection system is installed or required:
▶ Establish whether the thermal solar system is located outside the 

protective area of the existing lightning protection system.

▶ Have a qualified electrician check the connection of the system to this 

equipment. 

▶ Earth the installation system and metallic potable water pipes with a 

ground wire (e.g. copper ≥ 16 mm

2

) to the equipotential rail. 

▶ Lightning protection must only be installed by a qualified electrician.

Fig. 59   Possible connection of the lightning protection system to the 

storage tank profile rail

10.2

Filling the potable water circuit

CAUTION: 

Risk of injury from falling storage tank. 

Only filling with water ensures sufficient stabilisation of the storage tank. 

▶ Never leave the system before the filling process of the potable water 

circuit has been completed.

▶ Install a filter if required.
▶ Turn on the DHW tap until the pipework is filled.

10.3

Filling the solar circuit

CAUTION: 

Risk of injury from contact with heat transfer medium!

▶ When handling heat transfer medium, always wear protective gloves 

and goggles. 

▶ If heat transfer medium comes into contact with skin: wash the 

affected areas with water and soap. 

▶ If heat transfer medium comes into contact with eyes: holding eyelids 

wide open, thoroughly wash eyes with running water and consult a 
doctor.

▶ Operate the thermal solar system using heat transfer medium L. 

Other heat transfer media are not permitted. 

The heat transfer fluid is pre-mixed and ready to use (70 % water, 30 % 
propylene glycol). It guarantees safe operation down to -14 °C, protects 
the system from frost damage and ensures high steam safety.

Water as a heat transfer medium 

 section "Intended use".

NOTICE: 

Risk of property damage from unsuitable heat transfer medium. 

Using an unsuitable heat transfer medium can damage the thermal solar 
system through frost or chemical reactions.

▶ Only fill the thermal solar system with a heat transfer medium 

approved by the manufacturer.

Do not

 mix different heat transfer media together. 

▶ If the thermal solar system is not in use for more than 4 weeks: cover 

the collectors. 

The heat transfer medium is biodegradable. A 

safety data sheet

 with 

further information can be requested from the manufacturer.

Table 14  Required amount of heat transfer medium

▶ Fill the storage tank with heat transfer medium L from the top until it 

begins escaping from the filler. 

0010014919-01

0010016089-01

TSS150

TSS200

TSS300

8 l heat transfer 
medium

9 l heat transfer 
medium

12 l heat transfer 
medium

Summary of Contents for TSS Series

































Reviews: