background image

6 720 821 421 (2017/04)

Tronic 1000 T

Key to symbols and safety instructions | 3

1

Key to symbols and safety instructions

1.1

Key to symbols

Warnings

The following keywords are defined and can be used in this 
document:

NOTICE

 indicates a situation that could result in damage to 

property or equipment.

CAUTION

 indicates a situation that could result in minor to 

medium injury.

WARNING

 indicates a situation that could result in severe 

injury or death.

DANGER

 indicates a situation that will result in severe 

injury or death.

Important information

Additional symbols

1.2

Safety information

Installation

▶ The water heater must only be installed by an authorised 

person. 

Instructing the customer

▶ Do not operate this water heater until all operating 

instructions have been read and understood by the 
homeowner.

▶ Do not activate this water heater unless the cylinder is filled 

with water.

▶ Do not block or seal the relief safety valve or drain pipe.
▶ The water heater warranty can become void if relief valves 

or other safety devices are tampered with, or if the 
installation is not in accordance with these instructions.

▶ Do not place any articles, chemicals or flammable materials 

on or near the water heater.

▶ During the installation isolate the appliance from the power 

supply. 

▶ Removal of access covers will expose 240V wiring. Do not 

remove the terminal box cover unless the power supply has 
been effectively disconnected by an authorised person. 

▶ Do not operate this water heater with terminal box cover 

removed or loose.

▶ This water heater is not intended to be operated or 

adjusted by young children or infirm persons. Young 
children must be supervised to ensure they do not interfere 
with the water heater.

▶ This water heater is intended to be installed as a fixed 

appliance and must be installed on a hard, level surface. If 
installation is to be in a wet area or a concrete floor, ensure 
the water heater is mounted on a suitable and substantial 
raised base.

▶ If the electrical conduit to the water heater is damaged, it 

must be replaced by an authorised person in order to avoid 
a hazard. 

▶ For service of this water heater phone the Bosch TT Service 

Department on AU 1300 30 70 37, or NZ 0800 543 352.

Warnings in this document are identified by 
a warning triangle printed against a grey 
background.
Keywords at the start of a warning indicate 
the type and seriousness of the ensuing risk 
if measures to prevent the risk are not taken.

This symbol indicates important information 
where there is no risk to people or property.

Symbol Explanation

Step in an action sequence

 

Cross-reference to another part of the document

List  entry

List entry (second level)

Table 1

This water heater must be installed in 
accordance with:

Manufacturers Installation Instructions

AS/NZS 3500.4 “National Plumbing & 
Drainage Code”

AS/NZS 3000 “Wiring Rules”

Municipal Building Codes

Any other State or Federal Statutory 
Regulations

Summary of Contents for Tronic 1000 T

























Reviews: