background image

6 720 821 421 (2017/04)

Tronic 1000 T

Warranty details | 21

If the Product is not located within the usual operating area of 
an authorised service technician, the end user will be required 
to pay the service call costs associated with a service call under 
this voluntary warranty.

Notwithstanding the above, if the Product has not been 
installed in accordance with the installation instructions in 
regards to access, or has been otherwise installed in location 
where service access is difficult, the end user will be required 
to pay charges associated with the difficult access. This 
includes, but is not limited to, the removal of walls or doors to 
gain access and the use of specialised equipment to move the 
Product or components to safe working levels. Where the 
Product cannot be safely accessed, Bosch may refuse to 
service the Product under this voluntary warranty.

For invalid claims under this voluntary warranty, the end user 
will be liable for the costs of making the warranty claim 
including any service call costs.

Warranty Conditions

This voluntary warranty is subject to the following conditions:

The Product must have been installed and correctly 
commissioned by an authorised and licensed installer in 
compliance with applicable Australian Plumbing and Gas 
Standards. Proof may be required of correct 
commissioning of the Product (such as certificate of 
compliance). Claims for failures due to incorrect 
installation or commissioning are not covered under this 
voluntary warranty and may be rejected by Bosch.

Where a Product or part thereof is replaced or repaired 
under this voluntary warranty, the balance of the original 
voluntary warranty will apply. The replacement Product or 
part does not carry a new voluntary warranty.

The Product must have its original serial numbers and 
rating labels intact.

The warranty does not extend to any Product that has been 
completely or partially disassembled.

These warranty terms cannot be amended except in writing 
by an authorised officer of Bosch.

The warranty only applies to Product installed for an end 
user in Australia or New Zealand and purchased from 
Bosch or from a reseller where the Product has been 
originally sold by Bosch.

Any claim made under this voluntary warranty meets the 
requirements set out below in the “How to Make a Warranty 
Claim” section.

Warranty Exclusions

This warranty will not apply to a defect or fault to the extent to 
which it arises:

due to storage, handling or installation of the Product 
otherwise than in accordance with instructions provided 
for the Product by Bosch or without reasonable care, 
including installation of a Product which is of inappropriate 
size or type for the intended purpose;

due to operation, use or maintenance of the Product 
otherwise than in accordance with instructions provided 
for the Product by Bosch or without reasonable care, 
including use of the Product with faulty or unsuitable 
plumbing, water pressure, power or gas supply;

due to accidental damage or use of the Product for a 
purpose or in environmental conditions for which the 
Product were not designed or sold, or use of the products 
outside the specified or normal operating ranges for such 
Product.

as a result of changes which occur in the condition or 
operational qualities of the Product due to climate or other 
environmental influence, foreign material contamination or 
water entry or as a result of exposure to excessive heat or 
solvents or because of use of non-potable water or bore 
water in the Product or damage as result of an Act of Nature 
including but not limited to storms, fires, floods and 
lightning strikes;

from normal wear and tear or when replacement or repair 
of parts would be part of normal maintenance or service of 
the Product or where the damage is only to surface coating, 
varnish or enamel;

as a result of repairs, alterations or modifications to the 
Product which have been performed by a person who is not 
suitably qualified and experienced to perform works on the 
Product; or

from the use of any spare parts not manufactured, sold or 
approved by Bosch in connection with the repair or 
replacement of Product.

This voluntary warranty does not apply to damage that has 
been caused by continued use of a Product after it is known, or 
would have been known with regular servicing, it is defective.

Failure to service Product in accordance with recommendations in instruction manuals for Product may result in a warranty claim 
under this voluntary warranty being rejected by Bosch. Bosch alerts end users that instruction manuals for Product contain 
specific recommendations for servicing and safety checks to be carried out on Product.

Table 8

Summary of Contents for Tronic 1000 T

























Reviews: