background image

2

Bosch Rexroth Corporation

All rights are held by BOSCH REXROTH CORPORATION or
ROBERT BOSCH GMBH, also regarding patent claims. We retain all
powers of disposition, such as for copying and/or for passing-on to
third parties.

We reserve the right to make technical changes at any time
without notice.

Errors and omissions excepted.
© 2003 Bosch Rexroth Corporation

Table of contents

Page

• Important Safety Information ........................................................................................................................ 3

• Introduction ........................................................................................................................................................ 4

• Shipping Information ....................................................................................................................................... 4

• Assembly ............................................................................................................................................................. 5

• Preliminary Adjustments ................................................................................................................................ 5

• Operating Instructions ..................................................................................................................................... 8

• Maintenance ..................................................................................................................................................... 10

Liability:

In no event can the manufacturer accept warranty
claims or liability claims for damages resulting from
improper use of the equipment or as a result of
changes made to the equipment other than those
specified in this instruction manual.

Guarantee:

The manufacturer will accept no claims in which non-
original spare parts have been used. For information
on spare parts and replacement parts, contact Bosch
Rexroth Corporation.

Environmental Protection:

Always dispose of worn, damaged or obsolete parts
in a responsible manner.  It is the user’s responsibility
to dispose of all hazardous material such as adhesives
and cleaning solutions in accordance with all local,
state and federal guidelines.

Summary of Contents for Rexroth TSplus













Reviews: