manualshive.com logo in svg

Bosch Rexroth 10 Series, Instruction Manual

Share
Download
Bosch Rexroth 10 Series Instruction Manual Download Page 62

Bosch Rexroth AG, RE 91485-01-B/2021-11-18

62

/72

 

A10FZO, A10VZO, A10FZG and A10VZG series 10

 |  Disposal

12 Disposal

Careless disposal of the axial piston unit, the hydraulic fluid and the packaging 
material can result in environmental pollution.
Observe the following when disposing of the axial piston unit:

1� 

Completely drain the axial piston unit.

2� 

Dispose of the axial piston unit and packaging material in accordance with the 
regulations in your country.

3� 

Dispose of the hydraulic fluid in accordance with the regulations of your 
country. Also observe the applicable safety data sheet for the hydraulic fluid.

4� 

Disassemble the axial piston unit into its constituent parts for proper recycling.

5� 

For example, separate the parts into:

 

– Castings

 

– Steel

 

– Aluminum

 

– Non-ferrous metal

 

– Electronic waste

 

– Plastic

 

– Seals

Summary of Contents for Rexroth 10 Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands