manualshive.com logo in svg

Bosch Rexroth 10 Series, Instruction Manual

Share
Download
Bosch Rexroth 10 Series Instruction Manual Download Page 42

Bosch Rexroth AG, RE 91485-01-B/2021-11-18

42

/72

 

A10FZO, A10VZO, A10FZG and A10VZG series 10

 |  Installation

L

R

W

Abb� 23: Direction of rotation

W

Bi-directional (can rotate counter-clockwise and clockwise)

L

Counter-clockwise

R

Clockwise

The direction of rotation as indicated on the name plate determines the 
direction of rotation of the axial piston unit as viewed on the drive shaft; 
see chapter 5.3 "Product identification" on page 24. For information on 
the direction of rotation of the drive motor, please refer to the drive motor 
manufacturer's instruction manual.

7�5�2  Dimensions

For standard versions, the data sheet 91485 contains all required installation 
dimensions as well as the position and dimensions of the ports. If necessary, 
an installation drawing can be requested. Also observe the manuals provided by 
the manufacturers of the other hydraulic components when selecting the required 
tools.

7�5�3  General instructions

Follow these general notices when installing the axial piston unit:

 

• Note that certain installation positions will affect the control system. 

Gravity, dead weight and case pressure can cause minor characteristic shifts and 
changes in response time.

 

• Torsional vibrations and speed variations may cause increased rotary angular 

acceleration of the rotary group of the axial piston unit.

 

• If a shared drain line is used for several units, make sure that the respective 

case pressure in each unit is not exceeded. The shared drain line must be 
dimensioned to ensure that the maximum permissible case pressure of all 
connected units is not exceeded in any operating condition, particularly at cold 
start. If this is not possible, separate drain line must be laid, if necessary.

The version of installation for the axial piston unit depends on the connecting 
elements to the drive side. The following descriptions explain the installation of 
the axial piston unit:

 

• With a coupling

7�5�4  Installation with a coupling

The following describes how to install the axial piston unit with a coupling:

Summary of Contents for Rexroth 10 Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands