Bosch PSB 18 LI-2, Original Instructions Manual

Page: 14 / 203

14 | English
u
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
u
Use suitable detectors to determine if there are hid-
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
u
Always wait until the power tool has come to a com-
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
u
In case of damage and improper use of the battery, va-
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
u
Do not open the battery. There is a risk of short-circuit-
ing.
u
The battery can be damaged by pointed objects such
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
u
Only use the battery with products from the manufac-
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
u
Switch the power tool off immediately if the applica-
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for tightening and loosening
screws, as well as for drilling in wood, metal, ceramic and
plastic and for impact drilling in brick, masonry and stone.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Keyless chuck
(2) Torque presetting ring
(3) Operating mode presetting ring
(4) Gear selector switch
(5) On/off switch
(6) Rotational direction switch
(7) Battery release button
(8) Battery charge indicator
(9) Battery a)
(10) "PowerLight"
(11) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Cordless drill/driver PSB 18 LI-2
Ergonomic
Article number 3 603 JB0 3..
Rated voltage V= 18
No-load speed A)
– First gear min
-1
0–430
– Second gear min -1 0–1 400
Impact rate A) min -1 0–22,500
Max. torque, hard/soft screw-
driving application according to
ISO 5393 A)
Nm 32/28
Max. drilling diameter
– Steel
mm 13
– Wood mm 38
– Masonry mm 11
Max. screw diameter mm 10
Chuck capacity mm 1.5–13
Drill spindle thread 1/2"
Weight according to EPTA-Pro-
cedure 01:2014 B)
kg 1.6
Recommended ambient temper-
ature during charging
°C 0 to +35
Permitted ambient temperature
during operation
C)
and during
storage
°C –20 to +50
Recommended rechargeable bat-
teries
PBA 18V...W-.
Recommended chargers D) AL 18...
A) Measured at 20−25 °C with rechargeable battery PBA 18V
2.5Ah
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
D) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
1 609 92A 6DE | (16.06.2021) Bosch Power Tools