Bosch HGG223121Z, Instruction Manual

Page: 15 / 24

15
7.
The gas escaping from the gas grill is ignited using the
ignition button. To activate the safety pilot, press and hold the
function selector for 10 seconds.
The safety pilot is activated. If the gas flame goes out, the gas
supply is automatically interrupted by the safety pilot.
8.
Check that the flame is lit. If it is not, repeat the process from
step 5.
9.
When the dish has finished cooking, switch the function
selector off. Once the oven has cooled down, remove the
protective plate again.
:
Caution!
The ignition device should not be actuated for more than 15
seconds. If the burner does not light within 15 seconds, wait for
at least one minute. Then repeat the ignition process.
Care and cleaning
With attentive care and cleaning, your hob and oven will retain
its looks and remain in good working order for a long time. We
will explain here how you should care for and clean them
correctly.
Notes
■
Slight differences in the colours on the front of the oven are
caused by the use of different materials, such as glass,
plastic and metal.
■
Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
■
Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect operation. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Upper glass cover
Before opening the top cover, remove any spills with a cloth.
Use glass cleaner if possible.
For cleaning, remove the top cover. To do this, hold the cover
securely on both sides with both hands and pull it upwards.
If the cover hinges become loose, note the letters marked on
them. The hinge with the letter R must be fitted on the right, and
the hinge with the letter L must be fitted on the left.
After cleaning, re-assemble the top cover following the same
procedure in reverse order.
Only close the top cover once the burners have cooled down.
Cleaning agents
Damage to the various different surfaces caused by using the
wrong cleaning agent can be avoided by observing the
following instructions.
When cleaning the hob do not use
■
undiluted washing-up liquid or dishwasher detergent,
■
scouring pads,
■
abrasive cleaning agents such as oven cleaner or stain
remover,
■
high-pressure cleaners or steam jets.
■
Do not clean individual parts in the dishwasher.
When cleaning the oven do not use
■
sharp or abrasive cleaning agents,
■
cleaning agent with a high alcohol content,
■
scouring pads,
■
high-pressure cleaners or steam jets.
■
Do not clean individual parts in the dishwasher.
Wash new sponges thoroughly before first use.
Stainless steel
fronts
Wipe with some washing-up liquid and a damp cloth. Always wipe parallel to the natural grain. Otherwise,
you may scratch the surface. Dry with a soft cloth. Remove flecks of limescale, grease, starch and albumin
(e.g. egg white) immediately. Do not use any abrasive materials, scouring sponges or rough cleaning
cloths. The stainless steel fronts can be polished using a special care product. Follow the manufacturer's
instructions. You can purchase special stainless steel cleaner from our after-sales service or from specialist
retailers.
Enamel surfaces and
lacquered surfaces
Clean with some washing-up liquid and a damp cloth. Dry with a soft cloth.
Burners and steel
grid of the gas burn-
ers
Do not clean in the dishwasher. Remove the wire rack and clean with a sponge, washing-up liquid and
some hot water. Remove the burner cup and cap. Clean with a sponge and some hot water and washing-up
liquid. Ensure that the gas outlets on the burner cups are clean and unobstructed. Brush the igniters with a
small, soft brush. The gas burners only work properly when the igniters are clean. Remove food residue
from the burner shells with some washing-up liquid and a damp cloth. Only use a little water. Water must
not be allowed to enter the appliance. Ensure that the nozzle opening does not become blocked or dam-
aged during cleaning. Dry all parts after cleaning and place the burner cover accurately on the burner cup.
If the parts are not positioned accurately, it will be harder to ignite the burner. The burner covers are coated
with black enamel. Due to the high temperatures, discolouration may occur. This will not impair the function
of the burner. Replace the wire rack in the oven.
Electric hob (option)
Clean with the hard side of a scouring sponge and some liquid scouring agent. After cleaning, switch the
hob on briefly to dry it. Wet hobs rust over time. Then apply a care product. Always remove spilt liquids and
food residue immediately.