English |
47
Bosch Power Tools
1 609 92A 3S7 | (24.2.17)
Aligning the Fine Scale (see figure
N)
– Bring the power tool into the chop and mitre saw working
position. (see “Working Position”, page 43)
– Turn the saw table
22
to the 0° detent
27
. The lever
26
must be felt to engage in the detent.
Checking:
The 0° mark of the fine scale
46
must be in alignment with the
0° mark of the scale
23
.
Adjusting:
– Remove the insert plate
24
.
– Loosen the screw
55
with the slotted screwdriver provid-
ed and align the fine scale alongside the 0° marks.
– Retighten the screw again.
Aligning the Angle Indicator (Vertically)
(see figure
O)
– Bring the power tool into the chop and mitre saw working
position. (see “Working Position”, page 43)
– Turn the saw table
22
to the 0° detent
27
. The lever
26
must be felt to engage in the detent.
Checking:
The angle indicator
47
must be in alignment with the 0° mark
of the scale
48
.
Adjusting:
– Loosen the screw
56
with the slotted screwdriver provid-
ed and align the angle indicator alongside the 0° mark.
– Afterwards, check to ensure that the adjustment made is
correct for the 45° mark.
– Retighten the screw again.
Aligning the Fence
– Bring the power tool into the table saw working position.
(see “Working Position”, page 48)
– Turn the saw table
22
to the 0° detent
27
. The lever
26
must be felt to engage in the detent.
Checking:
(see figure
P1)
– Adjust an angle gauge to 90° and position it between the
fence
30
and the saw blade
7
on the saw table
22
.
The leg of the angle gauge must be flush with the fence over
the complete length.
Adjusting:
(see figure
P2)
– Loosen all hex socket screws
39
with the hex key
5
provid-
ed.
– Turn the fence
30
until the angle gauge is flush over the
complete length.
– Retighten the screws again.
Setting the Standard Bevel Angle 0° (Vertical)
– Bring the power tool into the table saw working position.
(see “Working Position”, page 48)
– Turn the saw table
22
to the 0° detent
27
. The lever
26
must be felt to engage in the detent.
Checking:
(see figure
Q1)
– Adjust an angle gauge to 90° and position it on the saw ta-
ble
22
.
The leg of the angle gauge must be flush with the saw blade
7
over the complete length.
Adjusting:
(see figure
Q2)
– Loosen the nut (size 10 mm) of the Allen screw
57
.
– Screw the Allen screw
57
with a suitable Allen wrench (size
3 mm) in or out until the leg of the angle gauge is flush with
the saw blade over the complete length.
– Retighten the nut again.
In case the angle indicator
47
is not in a line with the 0° mark
of the scale
48
after the adjustment, the angle indicator must
be aligned accordingly (see “Aligning the Angle Indicator (Ver-
tically)”, page 47).
Setting the Standard Bevel Angle 45° (Vertical)
– Bring the power tool into the table saw working position.
(see “Working Position”, page 48)
– Turn the saw table
22
to the 0° detent
27
. The lever
26
must be felt to engage in the detent.
– Loosen the lock lever
37
and tilt the tool arm leftward to
the stop (45°) by the handle
18
.
Checking:
(see figure
R1)
– Adjust an angle gauge to 45° and position it on the saw ta-
ble
22
.
The leg of the angle gauge must be flush with the saw blade
7
over the complete length.
Adjusting:
(see figure
R2)
– Loosen the nut (size 10 mm) of the Allen screw
58
.
– Screw the Allen screw
58
with a suitable Allen wrench (size
3 mm) in or out until the leg of the angle gauge is flush with
the saw blade over the complete length.
– Retighten the nut again.
In case the angle indicator
47
is not in a line with the 45° mark
of the scale
48
, firstly check the 0° setting for the bevel angle
and the angle indicator again. Then repeat the adjustment of
the 45° bevel angle.
Setting the Standard Bevel Angle 33.9° (Vertical)
– Bring the power tool into the table saw working position.
(see “Working Position”, page 48)
– Turn the saw table
22
to the 0° detent
27
. The lever
26
must be felt to engage in the detent.
– Loosen the lock lever
37
.
– Push the stop bolt
33
completely inside and swivel the tool
arm until the bolt faces against the stop screw
32
.
Checking:
(see figure
S1)
– Adjust an angle gauge to 33.9° and position it on the saw
table
22
.
The leg of the angle gauge must be flush with the saw blade
7
over the complete length.
Adjusting:
(see figure
S2)
– Loosen the nut (size 10 mm) of the stop screw
32
.
– Screw the stop screw with a suitable spanner (size 10 mm)
in or out until the leg of the angle gauge is flush with the saw
blade over the complete length.
– Retighten the nut again.
OBJ_BUCH-1688-007.book Page 47 Friday, February 24, 2017 12:15 PM
