14
| English
– Then push the base plate
(5)
towards the saw blade
(8)
as far as it will go.
– Retighten the screw
(15)
.
Moving the base plate (see figure D)
You can move the base plate
(5)
back for sawing close to
edges.
Loosen the screw
(15)
and push the base plate
(5)
towards
the mains cable as far as it will go.
Retighten the screw
(15)
.
Sawing with an offset base plate
(5)
is only possible with a
mitre angle of 0°. In all other cases the anti-splinter guard
(13)
may not be used.
Starting Operation
u
Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Switching on/off
u
Make sure that you are able to press the On/Off switch
without releasing the handle.
To
switch on
the power tool, press the on/off switch
(3)
.
To
lock
the on/off switch
(3)
, keep it pressed down and
push the locking mechanism
(1)
to the right or left.
To
switch off
the power tool, release the on/off switch
(3)
.
If the on/off switch
(3)
is locked, press the switch first and
then release it.
Controlling/preselecting the stroke rate
You can variably adjust the stroke rate of the power tool
when it is on by pressing in the on/off switch
(3)
to varying
extents.
Applying light pressure to the on/off switch
(3)
results in a
low stroke rate. Applying increasing pressure to the switch
increases the stroke rate.
It is not possible to reduce the stroke rate while the on/off
switch
(3)
is locked.
You can also preselect the stroke rate and change it during
operation using the stroke rate preselection thumbwheel
(2)
.
The required stroke rate is dependent on the material and
the work conditions and can be determined using practical
tests.
It is recommended that you reduce the stroke rate when
placing the saw blade on the workpiece and when sawing
plastic and aluminium.
During prolonged periods of use at a low stroke rate, the
power tool may heat up significantly. Remove the saw blade
and let the power tool run at the maximum stroke rate for
around three minutes to cool down.
Working Advice
u
Pull the plug out of the socket before carrying out any
work on the power tool.
u
Switch the power tool off immediately if the saw blade
becomes blocked.
u
When machining small or thin workpieces, always use
a stable base or saw table (accessory).
Before sawing into wood, chipboard, building materials,
etc., check for and remove any foreign objects such as nails,
screws, etc.
Plunge cutting (see figure E)
u
Plunge cuts may only be applied to soft materials,
such as wood, gypsum board, etc.
For plunge cutting, use only short saw blades. Plunge cutting
is possible only with a mitre angle of 0°.
Place the power tool so that the front edge of the base plate
(5)
rests on the workpiece, without the saw blade
(8)
touch-
ing the workpiece, and switch it on. On power tools with
stroke rate control, select the maximum stroke rate. Press
the power tool firmly against the workpiece and allow the
saw blade to plunge slowly into the workpiece.
As soon as the base plate
(5)
rests fully on the workpiece,
continue sawing along the required cutting line.
Coolant/lubricant
As the material heats up along the cutting line when cutting
metal, you should apply coolant or lubricant.
Maintenance and Service
Maintenance and Cleaning
u
Pull the plug out of the socket before carrying out any
work on the power tool.
u
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by
Bosch
or by an
after-sales service centre that is authorised to repair
Bosch
power tools.
Clean the saw blade receptacle regularly. For this, remove
the saw blade from the power tool and lightly tap out the
power tool on a level surface.
If the power tool becomes very dirty, this can lead to serious
faults. For this reason, do not cut materials which generate
large quantities of dust from below or overhead.
u
In extreme conditions, always use a dust extractor if
possible. Blow out ventilation slots frequently and in-
stall a residual current device (RCD) upstream.
When
machining metals, conductive dust can settle inside the
power tool, which can affect its protective insulation.
Apply a drop of oil to the guide roller
(7)
from time to time.
Check the guide roller
(7)
regularly. If worn, it must be re-
placed through an authorised
Bosch
after-sales service
centre.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
1 609 92A 5B3 | (16.07.2019)
Bosch Power Tools
