10
| English
3 609 929 C35 | (18.1.12)
Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
16.12.2011
Assembly
f
Before any work on the machine itself, pull the mains
plug.
Splash Guard / Auxiliary Handle
The splash guard
4
protects the machine against contamina-
tion and is used for fastening the auxiliary handle
7
. Slide the
splash guard
4
onto the spindle collar and then tighten the
clamping nut
9
.
Insert the auxiliary handle
7
into the drill hole of the splash
guard
4
, turn the auxiliary handle
7
to the requested positon
and lock it by shutting the clamping lever
8
.
Changing the Tool
Stirrer Paddle with Male Thread, Size M 14 (see figure A)
Screw the stirrer paddle
1
with the adapter
2
onto the drive
spindle
3
. Hold the drive spindle
3
in place with an open-end
spanner (size 22 mm) and tighten the adapter
2
and the stir-
rer paddle
1
with a second open-end spanner (size 22 mm).
The stirrer paddle is disassembled in reverse order.
Stirrer Paddle with External Hexagon
Screw the stirrer paddle
1
directly onto the drive spindle
3
.
Hold the drive spindle
3
in place using a open-end spanner
(size 22 mm) and, using a second open-end wrench (size
22 mm), tighten the stirrer paddle
1
.
The stirrer paddle is disassembled in reverse order.
Operation
Starting Operation
f
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
f
Dusts, e. g. mineral dusts, can be harmful to one’s health.
Contact with or inhaling the dusts can trigger allergic reac-
tions to the operator or bystanders and/or lead to respira-
tory infections.
Materials containing asbestos may only be worked on by
specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Switching On and Off
To
start
the machine, press the On/Off switch
6
and keep it
pressed.
Lock the
pushed
On/Off switch
6
by pushing the lock-on button
5
up-
ward.
To
switch off
the machine, release the On/Off switch
6
or
when it is locked with the lock-on button
5
, briefly press the
On/Off switch
6
and then release it.
Working Advice
The choice of stirrer paddle depends on the material to be
stirred. For materials with low viscosity, e. g., dispersion
paint, varnish, adhesions, casting compound, cement grout,
etc., use a stirrer paddle with left-hand spiral.
For materials with high viscosity, e. g., ready-mixed plaster,
concrete, cement, screed, filler, epoxy resin, etc., use a stir-
rer paddle with right-hand spiral.
While mixing, move the power tool in an up and down motion.
Clean the stirror paddle after use.
f
Avoid splashing around the material being stirred.
Oth-
erwise, you could slip and lose control over the power tool.
Maintenance and Service
Maintenance and Cleaning
f
Before any work on the machine itself, pull the mains
plug.
f
For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
OBJ_BUCH-322-002.book Page 10 Wednesday, January 18, 2012 8:33 AM
RAMIRENT
