Bosch FLEXIDOME NIN-733 Installation Manual Download Page 45

Page: 45 / 50

FLEXIDOME HD VR

Technical Data | en

Bosch Security Systems

Installation Manual

AM18-Q0637 | v1.1 | 2013.08

NIN-733

Audio signal-to-noise

ratio

> 50 dB

Memory card slot

Supports SDHC and SDXC microSD cards

Weight

0.84 kg (1.85 lb)

Environment

IP 66, NEMA Type 4X

Impact protection

IK10

Operating

temperature

-30 °C to +50 °C (-22 °F to +122 °F)

Imager

1/3-inch CMOS HD sensor

Image resolution

1280 × 720 pixels

Rated supply voltage

24 VAC 50/60 Hz

12 VDC

Power-over-Ethernet 48 VDC nominal

Current consumption

500 mA | 600 mA IVA (12 VDC)

450 mA | 500 mA IVA (24 VAC)

150 mA | 175 mA IVA (PoE 48 VDC)

Minimum illumination

Lens 3-9 mm, F1.2

0.017 lx Color, 30 IRE

0.0057 lx Mono, 30 IRE

Minimum illumination

Lens 10-23 mm, F1.6

0.03 lx Color, 30 IRE

0.01 lx Mono, 30 IRE

Day/Night

Color, Mono (IR contrast), Auto

Dynamic range

84 dB

Noise reduction

Intelligent Dynamic Noise Reduction (iDNR) with

separate temporal and spatial adjustments

BLC

Off, Auto, IntelligentAE (BLC)

White Balance

ATW, AWB hold and manual (2500 to 10000K)

Indoor and Outdoor ATW

Shutter

Automatic Electronic Shutter (AES)

Fixed (1/30 [1/25] to 1/150000) selectable

Default shutter

Contrast

enhancement

On/Off

Summary of Contents for FLEXIDOME NIN-733



















































Search results

Summary of Contents for FLEXIDOME NIN-733

Reviews:

Related manuals for FLEXIDOME NIN-733

Brands by name

Popular brands

Bosch FLEXIDOME NIN-733, Installation Manual

Search results

Summary of Contents for FLEXIDOME NIN-733

Reviews:

Related manuals for FLEXIDOME NIN-733

Brands by name

Popular brands