Bosch FLEXIDOME indoor 5100i User Manual Download | Manualshive

Page: 5 / 56

background image

FLEXIDOME indoor 5100i (IR) | FLEXIDOME
outdoor 5100i (IR)

Browser connection | en

5

Bosch Security Systems B.V.

User manual

11-2022 | V02 | F.01U.394.427

1

Browser connection

A computer with a web browser (Google Chrome, Microsoft Edge, or Mozilla Firefox) is used
to receive live images, control the unit, and replay stored sequences. The unit is configured
over the network using the browser.

1.1

System requirements

Our recommendations are:
–

Computer with Dual core HyperThreading processor or better

–

Graphic card with performance that matches or is better than the resolution of the
camera

–

Windows 10 or later

–

Network access

–

Google Chrome, Microsoft Edge, or Mozilla Firefox

- or -

Application software, for example, Video Security Client, Bosch Video Client or BVMS.

Note:

To see live images in your browser it might be necessary to download and install the MPEG-
ActiveX from the Bosch download store.

1.2

Establishing the connection

The device must have a valid IP address to operate on the network and a compatible subnet
mask.
By default, DHCP is pre-set at the factory

On plus Link-Local

so a DHCP server assigns an IP

address or, if no DHCP server is available, a link local address (auto-IP) is assigned within the
range 169.254.1.0 to 169.254.254.255.
The Project Assistant app or Configuration Manager can be used to find the IP address.
Download the software from

https://downloadstore.boschsecurity.com

1.

Start the web browser.

2.

Enter the IP address of the device as the URL.

3.

During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must
configure the device before the device can communicate with the network.
To configure the device, connect it directly to a computer using a network cable and then set
the service-level password.

Note:

If you cannot connect, the unit may have reached its maximum number of connections.
Depending on the device and network configuration, each unit can have up to 50 web browser
connections, or up to 100 connections via Bosch Video Client or BVMS.

1.3

Password protection in camera

The device is password-protected. The first time that any user accesses the device, the device
will prompt the user to set a password at the service level.
The camera requires a strong password. Follow the prompts in the dialog box, which specifies
what is required. The system measures the strength of the password that you enter.
Make sure the password obeys these conditions:
–

8 to 19 characters in length

–

Upper and lower case letters

–

Minimum of 1 digit

«
...
3
4
5
6
7
...
»

Summary of Contents for FLEXIDOME indoor 5100i

























































Reviews:

No comments

Related manuals for FLEXIDOME indoor 5100i

Brand: KanDao Pages: 49

Brand: Samsung Pages: 28

Brand: Pentax Pages: 124

Brand: Papago Pages: 100

Brand: FashionCam Pages: 6

Brand: Foscam Pages: 2

DirectCX TC-T5531WRX

Brand: Idis Pages: 18

IP WEBCAM MT4009

Brand: media-tech Pages: 38

CeilingVIEW SD CCU

Brand: VADDIO Pages: 16

Brand: Conbrov Pages: 36

Brand: Gator Pages: 16

Brand: WolfVision Pages: 20

Brand: Yada Pages: 57

Brand: Alpine Pages: 4

Brand: Gator Pages: 18

Brand: Microdigital Pages: 11

Brand: Wixey Pages: 4

Brand: Sercomm Pages: 121

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands