background image

fr   Guide d'installation

Détecteur IRP/hyperfréquences 

de plafond TriTech

DS9360

© Bosch Security Systems

 B.V

.

, 2021

 

Torenallee 49, 5617 BA Eindhoven, Netherlands

 

9 Other Information
9.1 Anti-Vandal Screws

After the cover has been installed and twisted into place, the entire 

assembly can be secured together using the supplied anti-vandal screws. 

Refer to the Top View of Enclosure in 

Figure 2.2 

for the location of the 

screw holes.

9.2 Maintenance

At least once a year, the range and coverage should be verified. To en-

sure continual daily operation, the end user should be instructed to walk 

through the far end of the coverage pattern. This ensures an alarm output 

prior to arming the system.

Bosch Security Systems

 B.V

. product manufacturing dates

Use the serial number located on the product label and refer to the Bosch 

Security Systems

 B.V. 

web site at: http://www.boschsecurity.com/datecodes/.

8 Supervision Features

The supervision features function as follows:

PIR/Microwave:  The complete circuit operation of these subsystems

is checked approximately every 6 hours. If the PIR or microwave

subsystem fails, the red LED will flash 4 times per cycle and the unit

should be replaced.

Default:  The detector will default to PIR technology protection if the

microwave subsystem fails.

MIN

MAX

Microwave

Adjustment

NOTICE!

Do not adjust the microwave range higher than required. Doing so 

may cause the detector to catch movement outside of the intended 

coverage pattern.

Figure 6.2: Adjusting microwave range

3. If adequate range can not be reached, increase the Microwave Range

Adjust slightly. Continue walk testing (waiting 1 minute after removing/

replacing the cover) and adjusting the range until the farthest edge of

desired coverage has been accurately placed.

4. Walk test the unit from all directions to determine all the detection

pattern boundaries.

Summary of Contents for DS9360









Reviews: