manualshive.com logo in svg

Bosch CCS800, Service Manual

Share
Download
Bosch CCS800 Service Manual Download Page 18

CCS800 | 

Service manual | Chapter 3 | Controls and indicators 

en | 16 

 

 

Bosch Security Systems | 2005-01| 3922 880 21112 

3.2 

Delegate and chairman units 

 

 

Top 

 

Microphone 

Electret microphone with build-in plop and windshield, mounted on a 
flexible stem, complete with a red LED light-ring 

Light-ring around the microphone 

Indicates if microphone is switched ON 

Button (S2) 

Microphone ON button 

Red LED 

Indicates if microphone is switched ON 

 

Rear 

 

Trunk input 

Cable, 2 meter, with 7-pole DIN-connector. 

Trunk output 

Loop-through output socket, 7-pole DIN. 

 

Side 

 

Thumbwheel (R54) 

Rotary volume control for headphones. 

Headphone jack s(X6/X7) 

2 x 3.5 mm stereo jack headphone sockets. 

 

Inside 

 

Adjustment microphone capsule (R72) 

Potentiometer to adjust the sensitivity of the microphone (Access via 
bottom hole. See chapter 5). 

Additional for chairman units 

 

Top 

 

Button (S1) 

Priority function (chime tone) 

 

Bottom 

 

Small bracket at cable entry 

Hides the priority and chime mode switch (see “Instructions for use”). 

2 Switches behind bracket 

Delegate microphones off at priority (S37) 

Chime en-/disable switch (S42) 

 

Summary of Contents for CCS800









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands