background image

6/54 

Safety instructions | Automax 100 | Basic module TS-AC B1-M2-1X 

Bosch Rexroth AG | 04.2021 | DOK-SUPPL*-TS-AC B1-M2-ITRS-EN-P 

2.3

 

Improper use  

Any use deviating from the intended use is improper and thus not admissible. 

Bosch Rexroth AG does not assume any liability for damage caused by improper use. The 
user assumes all risks involved with improper use. 

Improper use of the product is defined as in particular: 

 

Exposure to operating conditions which do not satisfy the prescribed environmental 
conditions. Examples of prohibited operation include operation under water, under 
extreme temperature variations or extreme maximum temperatures 

2.4

 

Qualification of personnel  

2.4.1

 

General informations 

Basic mechanical and electric knowledge as well as knowledge of corresponding technical 
terms is required for assembly, commissioning, maintenance (incl. service, inspection, 
repair) and disassembly. To ensure operational reliability, these activities may therefore only 
be performed by a qualified expert or an instructed person under the supervision of an 
expert. Experts are those who are able to recognize potential dangers and apply the 
appropriate safety measures due to their professional training, knowledge and experience, 
as well as their understanding of the relevant conditions pertaining to the work to be 
undertaken. An expert must observe the relevant specific professional rules. 

2.4.2

 

Teaching 

At this product, trainees may only work: 

 

under direct supervision 

 

after being given appropriate instructions 

by an instructor or trained member of staff. 

2.4.3

 

Trained personnel 

For the supervision during the exercises, trained personnel may also be used. 
These are qualified people who were instructed and briefed in relation to: 

 

Tasks ordered 

 

Possible dangers in the event of improper use 

 

Safeguards and protective measures 

2.5

 

General safety instructions  

 

Observe the valid regulations on accident prevention and environmental protection 

 

Observe the safety regulations and provisions of the country where the product is 
implemented/used 

 

Exclusively use Rexroth products in technically perfect condition.  

 

Observe all notes on the product 

 

Persons permitted to assemble, operate, disassemble or maintain Rexroth products must 
not be under the influence of alcohol, other drugs or medication which can impair 
responsiveness when doing so 

 

Only use spare parts approved by the manufacturer in order to exclude hazards to 
persons due to unsuitable spare parts 

 

Comply with the technical data and environmental conditions specified in the product 
documentation 

Summary of Contents for Basic module TS-AC B1-M2-1X





























































Reviews: