Bosch AVIOTEC IPSTARLIGHT 8000 Operation And Commissioning Manual Download Page 47

Page: 47 / 70

AVIOTEC IP starlight 8000

Technical data | en

Bosch Sicherheitssysteme GmbH

Operation and Commissioning Manual

2020.08 | 01 | F.01U.391.015

Technical data

Algorithm Overview

Min. detection size for Smoke, standard setting
(% of picture width)

1.6

Smoke speed
(% of picture height /s)

0.7 - 8.4

Min. Smoke density (%)

Min. detection size for Flame, standard setting
(% of picture width)

1.1

Min. illumination level (lx)

Min. illumination level with IR illumination (lx)

Environmental

Operating Temperature

-20°C to +50°C (-4°F to 122°F)

Storage Temperature

-30°C to +70°C (-22°F to +158°F)

Operating Humidity

20% to 93% RH

Storage Humidity

up to 98% RH

Input/output

Analog video out

SMB connector, CVBS (PAL/NTSC), 1 Vpp, 75 Ohm

Audio line in

1 Vrms max, 18 kOhm typical,

Audio line out

0.85 Vrms at 1.5 kOhm typical,

Audio connectors

3.5 mm mono jack

Alarm input

2 inputs

Alarm input activation

+5 VDC nominal; +40 VDC max. (DC-coupled with 50 kOhm
pull-up resistor to +3.3 VDC)
(< 0.5 V is low; > 1.4 V is high)

Alarm output

1 output

Alarm output voltage

30 VAC or +40 VDC max.
Maximum 0.5 A continuous, 10VA (resistive load only)

Ethernet

RJ45

Data port

RS‑232/422/485

Local storage

Internal RAM

10 s pre-alarm recording

Memory card slot

Supports up to 32 GB microSDHC / 2 TB microSDXC card.
(An SD card of Class 6 or higher is recommended for HD
recording)

Summary of Contents for AVIOTEC IPSTARLIGHT 8000







































































Search results

Summary of Contents for AVIOTEC IPSTARLIGHT 8000

Reviews:

Related manuals for AVIOTEC IPSTARLIGHT 8000

Brands by name

Popular brands

Bosch AVIOTEC IPSTARLIGHT 8000, Operation And Commissioning Manual

Search results

Summary of Contents for AVIOTEC IPSTARLIGHT 8000

Reviews:

Related manuals for AVIOTEC IPSTARLIGHT 8000

Brands by name

Popular brands