Bort 91278166, User Manual

Page: 3 / 26

3
- Use a Residual Current Device (RCD) of not more
than 30 mA, at the plug socket when using this appli-
ance.
- INJURY HAZARD.
The high pressure may cause materials to bounce off
surfaces at speed; therefore protective clothing and
safety goggles MUST BE WORN.
- ACCIDENTAL START-UP HAZARD.
Before doing work on the cleaner, REMOVE the plug.
- INJURY HAZARD.
Before pressing the trigger, GRIP the gun firmly to
counteract the recoil.
- CONTAMINATION HAZARD.
COMPLY WITH the requirements of the local water
supply company. According to DIN 1988, power-jet
cleaners may only be connected to the mains drinking
water supply if a backflow preventer valve with drain
facility is installed in the supply hose.
- ACCIDENT HAZARD.
Maintenance and/or repair of electrical components
MUST be carried out by qualified staff.
- INJURY HAZARD.
DISCHARGE residual pressure before
disconnecting the cleaner hose.
- ACCIDENT HAZARD.
Before using the cleaner, CHECK every time that the
screws are fully tightened and that there are no broken
or worn parts.
- EXPLOSION AND ELECTRIC SHOCK HAZARD.
Only USE detergents which will not corrode the coat-
ing materials of the high pressure hose/electrical ca-
ble.
- INJURY HAZARD.
ENSURE that all people or animals keep a minimum
distance of 16 yd. (15m) away.
SAFETY VALVE
The safety valve also functions as a pressure limiting
valve. When the gun trigger is released, the safety valve
opens and the water recirculates through the pump inlet.
3. ASSEMBLY
High pressure washer KEX-3000 comes assembled and
ready for use.
CONNECTION
1. Attach the high pressure hose to the pressure water
outlet of the machine.
2. Attach the spray handle to the high pressure hose.
Prior to operating the machine please ensure that the
high pressure hose has been completely uncoiled.
Whilst the machine is in operation the hose MUST not
loop.
3. Mount the nozzle or any other equipment you want
to use.
4. Connect the machine to the water and power supplies.
INSTALLATION, ELECTRICAL AND WATER
CONNECTIONS
(fig 1)
1. pressure cleaner
2. water supply hose
3. water connection
4. water inlet
5. high pressure tube
ment parts authorized by the manufacturer. The use of
original accessories and replacement parts will ensure
safe, trouble-free operation.
● The cleaner must be used standing on a secure, sta -
ble surface.
● Avoid unintentional firing of the trigger. Do not carry
the lance/ trigger assembly with your hand over the
trigger. Always use the trigger lock mechanism.
● Ensure that the safety lock on the trigger is used,
when you have stopped using the pressure washer to
prevent accidental operation.
SAFETY “MUST NOTS”
- EXPLOSION OR POISONING.
DO NOT use the cleaner with inflammable or toxic liq -
uids, or any products which are not compatible with
the correct operation of the cleaner.
- INJURY HAZARD.
DO NOT direct the water jet towards people or ani-
mals.
- ELECTRIC SHOCK HAZARD.
DO NOT direct the water jet towards the unit itself,
electrical parts or towards other electrical equipment.
- SHORT CIRCUIT HAZARD.
DO NOT use the cleaner outdoors in case of rain.
- INJURY HAZARD.
DO NOT allow children or incompetent persons to use
the cleaner.
- ELECTRIC SHOCK HAZARD.
DO NOT touch the plug and/or socket with wet hands.
- ELECTRIC SHOCK AND SHORT CIRCUIT HAZARD.
DO NOT use the cleaner if the electrical cable is dam-
aged.
- EXPLOSION HAZARD.
DO NOT use the cleaner if the high pressure hose is
damaged.
- ACCIDENT HAZARD.
DO NOT jam the trigger in the operating position.
- ACCIDENT HAZARD.
Check that the data plates are affixed to the cleaner, if
not, inform your dealer. Cleaners without plates must
NOT be used as they are unidentifiable and potentially
dangerous.
- EXPLOSION HAZARD.
DO NOT tamper with or alter the calibration of the
safety valve.
- HAZARDOUS ALTERATION OF OPERATING PER -
FORMANCE.
DO NOT alter the original diameter of the spray head
nozzle.
- ACCIDENT HAZARD.
DO NOT leave the cleaner unattended.
- SHORT CIRCUIT HAZARD.
DO NOT move the cleaner by pulling on the electrical
cable.
SAFETY “MUSTS”
- SHORT CIRCUIT HAZARD.
All electrical conductors MUST BE PROTECTED
against the water jet.
- ELECTRIC SHOCK HAZARD.
The cleaner MUST ONLY BE CONNECTED to a cor -
rectly earthed power supply.