Bort 91275752, Installation Instructions Manual

Page: 11 / 34

11
1. Put the lange (2) on the drain pipe Insert the
rubber seal (1). Fasten drain tube, tightly pulling it
to the body disposer with screws (4). (Fig. 9.1)
9. CONNECTING THE DISPOSER TO THE ELECTRI-
CAL NETWORK
ATTENTION! ELECTRIC SHOCK CURRENT
• To prevent electric shock, turn of the power
before installing or servicing the product.
• If you are not qualiied enough, call an electrician
to connect the product to the power.
• If a three-pin grounding-type plug is used to
connect a three-contact outlet with ground.
• Do not modify the design of the plug supplied
with the device.
• Improper equipment grounding may cause
electric shock current.
• All electrical connections must comply with the
electrical and norms.
• Do not connect the ground to the feed pipe gas.
• Do not power on the distribution shield until you
have installed the sockets with proper grounding.
• If the power cord is damaged, it must be replaced
at the service center.
NOTE: Access to a grounded outlet is required.
Installing all additional outlets must be carried out
by a qualiied electrician, and all outlets must be
properly grounded.
Turn ON/OFF device
Depending on the models BORT disposer are
equipped with two types of control: a wireless (wall)
switch or a pneumatic switch.
Wireless (wall) switch
The disposer of the “Control and FullControl” series
are equipped with a wireless wall mount switch.
The switch should be located in a convenient (safe
for children) place above the table top.
For instal the switch to the wall, use double-sided
tape.
For activate / deactivate the device, hold down the
key for 2-3 seconds.
Battery type: Voltage: 12V; Size: A27
Air switch
Disposer is equipped with an air switch and a
connecting pipe (except “Control” series).
INSTALLATION OF AIR SWITCH
1. Drill a hole with a diameter of 25 mm in suitable
top or top the panel of a sink. Some sinks may
already have a suitable A hole for the opening of
which is necessary remove the cover.
2. Unscrew the nut from the body of the push
button, while holding the stainless steel washer and
rubber gasket in place. Place one end of the PVC
tube on the spout on the body Press the other end
to A hole in the table top and a nut located under
the countertop. (Fig. 10.2)
3. Place the push button housing in the hole and
tighten the nut underneath countertop (enough
arm efort). Do not use the key to tighten nut. (Fig.
10.3)
4. Take the other end of the duct and tightly put it on
the spout of the air switch located on the bottom of
the disposer. (Fig.10.4) Hand tighten the clamping
nut. The disposer installation is complete. Before
using the product, read all of the instructions.
operation and safety contained in paragraph 10 of
this manual. In conclusion, install the plug in the
sink in the Closed position. Fill the sink with water,
Remove the plug and check the connections on the
a water leakage.
10. ATTENTION! IMPORTANT INSTRUCTIONS FOR
SAFETY
• If the air switch does not work, remove the plug
power supply from the outlet and check the air
duct pneumatic switch and delivered to the outlet
electricity.
• This product is designed for grinding food residues
at home; the ingress of substances other than food
into the disposer may cause injury and / or damage
property. To reduce the risk of Do not use a washer
with an installed disposer not for food purposes (for
example, for bathing a child or washing your head).
• Children should be supervised adults and should
not play with a disposer. To reduce the risk of injury
It is necessary to keep a watchful eye on children
use of the product.
• If the wedging in the disposer is eliminated,
turn of the appliance and disconnect it from the
electrical network. Use a wrench for self-removal
of jammed waste according to description in the
section “Elimination of jamming disposer “.
• Use tongs or pliers to remove foreign objects from
the product.
• To reduce the risk of injury from particles that are
thrown out by the disposer, it is prohibited to use
grinders withoutnoise shielding screen (Fig.8.3).
Place the plug in the drain hole, as shown in Fig.
11.2 or 11.4.
Do not allow the following items to fall into the
disposer: shells, including oyster, caustic means for
cleaning pipes or similar chemical products, glass,
porcelain or plastic, large (hollow) bones, metal
objects (bottle caps, cans, or kitchen appliances),
hot fat or other hot liquids.
• Replace worn noise glossy screen / installation
gasket / protective relector if they are worn and are