background image

Page 16

X. Questions and answers

During operation of the device, the temperature indicated on the external thermometer is 

higher than set on the thermostat.

When working in an empty chamber, the air stream passes through the centre where the 

tip of the thermometer is located. Temperatures should be the same when working with the 

charge,  which  causes  mixing  of  warm  air  and  its  even  distribution  in  the  whole  chamber. 

Temperature differences may also be affected by atmospheric conditions.

The thermostat has turned off, the temperature in the chamber is still increasing.

The temperature in the chamber increases after turning off the thermostat due to inertia.

So the heating element releases heat accumulated in itself after turning off for a certain time. 

For stable operation of the device, it is recommended to place a bowl with water under the 

generator burner. This improves the temperature stability inside the chamber.

The chips burn on the smoke generator burner.

Do  not  connect  the  smoker  chimney  outlet  to  chimneys,  ventilation  shafts  or  other 

extensions of the smoke outlet due to the possibility of producing draft in the smoker, which 

can  cause  wood  chips  to  ignite.  The  only  way  that  is  acceptable  for  extending  the  smoke 

outlet, is to apply a hood over the smoker so that smoke can be extracted from the smoker at 

its own speed.

Igniting wood chips may cause accumulated carbon deposit on the feeder and unfavourable 

weather conditions (e.g. wind gusts). Both these factors should be eliminated by removing the 

carbon deposit and protecting the smoker from the gusts of wind or covering the air inlet 

under the smoke generator.

Smoke is led outside at the bottom of the smoker or through the smoke generator.

  The chimney is too closed, it should be tilted enough to let the smoke come out only 

through it.

There is no smoke escaping from the chimney.

No smoke is a sign that a flame has appeared on the smoke generator. Stop the smoke 

generator immediately and put out the flame. The reason for this phenomenon may be the 

connection of the smoker to chimney flues or gusts of wind.

Summary of Contents for BBD-150


















Reviews: