Owner’s Manual
OS OUTDOOR SPEAKERS
INTRODUCTION
The TDG Audio OS Series Outdoor Speakers are all-weather loudspeakers that bring an amazing audio experience outdoors. Enjoy great sound with drivers
tuned to perfec�on. The OS speakers are available in black or white UV treated ABS enclosures along with color matched aluminum grills.
WIRING
1. A�ach the speaker cables to the speaker cable terminals on the back of the OS speaker.
2. Connect the speaker cable while ensuring proper polarity with the amplifier, + to + (red) and - to - (black).
3. Also ensure that the right channel of the amplifier is connected to the right speaker and the le� channel to the le� speaker.
PLACEMENT
Outdoor Installa�ons
1. When moun�ng the OS speakers outdoors, the eaves of the roof provide an ideal loca�on as they reduce the exposure of constant
direct sunlight and precipita�on.
2. If installing speakers on a boat, the wheelhouse provides the best loca�on for the same reasons.
Indoor Installa�ons
1. When placing the OS speakers on a wall or bookshelf, we recommend that they are mounted at ear level or slightly higher.
2. The usual listening area should be no closer to the speakers than the distance between the speakers themselves.
MOUNTING
1. The OS speaker is supplied with a U shaped wall moun�ng bracket that can be installed ver�cally or horizontally.
2. Use screws, bolts or anchors (not included) that are capable of suppor�ng the weight of the speaker to mount the bracket.
3. Choose a moun�ng surface with sufficient strength to reliably hold the speaker.
4. Mount U bracket with slots poin�ng upward if moun�ng horizontally.
5. Once the bracket is securely fastened, insert knob screws loosely on to the speaker and slide on to bracket.
6. Rotate the speaker to desired posi�on and �ghten the knob screws.
7. To �lt the speaker, loosen the two thumb screws a�aching the U bracket and wall mount plate. Tilt speaker to desired posi�on and
�ghten the two thumb screws securely.
8. For 70v/100v installa�ons, select the desired voltage se�ng on the top of the rear enclosure.
PAINTING
The grille and cabinet of your speakers may be painted. For best results, lightly sand all surfaces to be painted (cabinet and grille). Wash
these surfaces with a moustened cloth dipped into a mild detergent to remove any fingerprints or grease. Allow speaker to dry before
pain�ng. Care must be taken to mask off the front of the speaker to protect the tweeter, woofer, and front panel from overspray. This will
main�ng the exis�ng uniform dark color behind the grille and protect the woofer and tweeter from being damaged by the paint.
PORT PLUGS
Gently remove the speaker grill and insert port plugs to port tubes on the front speaker baffle to turn the OS speakers into a sealed
enclosure. Highly recommended when installing OS speakers in loca�ons with water spray or water splash.
SPECIFICATIONS
OS-82T
0S-62T
FREQUENCY RANGE
50Hz - 20kHz +/- 3dB
55Hz - 20kHz +/-3dB
HIGH FREQUENCY DRIVER
1" (25.4mm) Aluminum TW
1" (25.4mm) Aluminum TW
LOW FREQUENCY DRIVER
8" (203.2mm) Aluminum WF
6.5” (165mm) Aluminum WF
SENSITIVITY
88 dB
88dB
POWER HANDLING
50W RMS
50W RMS
70V TAP SETTINGS
50W, 25W, 12.5W, 6W
50W, 25W, 12.5W, 6W
100V TAP SETTINGS
*DNC, 50W, 15W, 12.5W
*DNC, 50W, 15W, 12.5W
IMPEDANCE
8 Ohm
8 Ohm
ENCLOSURE MATERIAL
UV Treated, Glass-Filled ABS Cabinet
UV Treated, Glass-Filled ABS Cabinet
ENCLOSURE TYPE
Ported
Ported
FINISH
Black or White Ma�e, Paintable
Black or White Ma�e, Paintable
PRODUCT DIMENSIONS
11” x 17.5” x 13.4”
8.5” x 13.5” x 10.6”
(285mm x 443mm x 340mm)
(216mm x 343mm x 270mm)
PRODUCT WEIGHT
17 lbs (7.7 kg)
8.6 lbs (3.9 kg)
*DNC - Do Not Connect
