Booxt 2007 GOES 300 S Service Manual Download Page 59

Page: 59 / 188

ENGINE

Cam Lobe Height

Intake

Std: 35.16 mm

Limit: 35.11 mm

Exhaust

Std:

35.05 mm

Limit: 35.00 mm

3. If not removing the cylinder for other service, secure

the cam chain with a wire to prevent it from falling into the

crankcase.

4. Inspect cam sprocket teeth for wear or damage.

Replace if necessary.

2. Thoroughly clean the cam shaft

3. Measure height of each cam lobe using a micrometer.

Replace cam if worn below minimum height.

Replace camshaft if damaged or if any part is worn

excessively.

CAMSHAFT INSPECTION

1. Visually inspect each cam lobe and bearing for wear,

chafing or damage.

4.11

Summary of Contents for 2007 GOES 300 S





























































































































































































Search results

Summary of Contents for 2007 GOES 300 S

Reviews:

Related manuals for 2007 GOES 300 S

Brands by name

Popular brands

Booxt 2007 GOES 300 S, Service Manual

Search results

Summary of Contents for 2007 GOES 300 S

Reviews:

Related manuals for 2007 GOES 300 S

Brands by name

Popular brands