background image

                                           

BKS Terminal Disinfection Robot Product Manual v1.0 

BooCax Robotics

 

 

1

  / 

24

 

www.boocax.com

 

Safety and Use Precautions 

Please follow the operation instructions of the product when using the robot.

 

It 

is forbidden to use beyond the scope

The company will not assume any responsibility 

for the loss caused by improper operation beyond the standard. 

01/

 

Instructions on safety matters in use of robots 

1)

 

Behaviors below are prohibited

 

Stay in the space where the robot is disinfecting

 

 

Robots are used in flammable gases and similar hazardous environments

 

 

Add any disinfectant not suitable for this product to the tank

 

 

Cleaning, wiping and other non-necessary operations when the robot is on

 

 

Unauthorized disassembly of the robot for repair or debugging

 

 

Touch the circuit terminal while the robot is charging

 

 

Replace any parts without authorization (If necessary, please do so under the company's 
approval and guidance); 

 

To transport the robot while its tank is still with hydrogen peroxide disinfectant 

2)

 

Safety instructions for use 

 

The robot should be parked and run as far as possible in a flat, solid, normal 
temperature condition

 

 

When adding hydrogen peroxide, do not splash to other parts of the robot

 

 

If abnormal sound is found during the disinfection work, please immediately turn off the 
power of the robot and report to the after-sales service for treatment

 

 

Before starting the robot, please check whether the safety device (sensor, emergency 
stop switch, etc.) is normal

 

 

If discover the road with water and greasy, please clean the road, to remove greasy

 

 

When to maintain the robot, it must be carried out by trained professionals; 

 

If the robot is not to use for a long time, it must keep the tank out of any liquid and 
promote it to a cool and dry place for preservation

 

02/

 

Safety instructions for using hydrogen peroxide   

Please strictly comply with all requirements of hydrogen peroxide. 

03/

 

Daily maintenance instructions 

When cleaning the tank, please use the matching cleaning detergent, make sure the robot is 

power off and unplugged or away from the charging pile

Otherwise, electric shock or serious 

failure may occur. 

It is strictly prohibited to flush the robot and charging pile directly with tap water, which may 

lead to the accumulation of water vapor or water inside the equipment and cause serious 
irreparable failure. 

Summary of Contents for BKS-ST-180A


























Reviews: