manualshive.com logo in svg

Bonart KRUUSE-SP1, Instruction Manual

Share
Download
Bonart KRUUSE-SP1 Instruction Manual Download Page 23

 

- 22 - 

of the system.   

 

System operates: 

 

No water reaches the tip (scaling mode) 

1.

 

Assure that the water control knob is turned on or adjusted to allow water to flow (turning 

counter-clockwise allows for more water). 

2.

 

Check that the water supply control valve (dental office water supply) is open. 

3.

 

Check that the external water tube is properly connected.   

 

9-B Technical Support and Repairs 

For  technical  support  and  assistance  call  1-888-526-6278  or  626-600-5330  Monday  through 

Friday,  9:00  AM  to  5:00  PM  (Pacific  Time).  For  other  areas,  contact  your  local  Bonart 

representative.. 

 

X: Specifications

 

 

Classification 

 

Protection against electric shock

：

Class I 

 

Degree of protection against electric shock

：

Type BF 

 

Mode of operation

：

Continuous 

 

Medical device directive

：

IIa   

 

Standards Followed 

ISO13485: 

Medical Devices, Quality Management Systems, Requirements for regulatory 

purposes 

93/42/EEC: 

MDD CE Directive 

EN60601-1: 

 

Medical Electrical Equipment, General Requirement for Safety 

EN60601-1-2: 

Medical Electrical Equipment, Electromagnetic Compatibility,   

Requirements and Tests 

Summary of Contents for KRUUSE-SP1

























Reviews:

No comments

Brands by name

Popular brands

Load more brands