background image

D

UAL 

C

YCLE 

-

 

R

EFRIGERATED 

C

OOLING 

C

OMPONENT

 

 
 

 
 

Page 22 

Commissioning 

Installation Instructions 

Commissioning 

C

OMMISSIONING 

C

HECK 

L

IST

 

Site 

 

Return panels and covers to their correct position and check that they are well secured. 

 

Ensure all service caps are fitted and correctly tightened. 

 

Attach the electrical wires and pipes to the wall with clamps. 

 

Check all the operations of the air-conditioner.  Follow the operating manual for 
instruction. 

Indoor Coil 

 

Is the condensate drain fixed securely and has it been tested? 

 

Are all ducting connections secured and free from air leaks? 

Outdoor Unit 

 

Check for any abnormal noise or vibrations during operation of the air conditioner. 

 

Check that the noise, condensate drainage or air flow does not disturb the neighbors. 

 

Run the dual cycle system for cooling and check operation. 

Customer Handover 

 

Explain to the customer together with the operating instructions 

 

How to remove, clean and replace the filter 

 

How to turn the air-conditioner on and off. 

 

How to choose between heating and cooling and how to set the desired temperature. 

 

How to operate the air conditioner from the controller. 

 

Ensure the warranty details are completed correctly.  The warranty section is found in 
the rear of the owner’s manual. 

 

Ensure the model and serial number sticker is inserted in the warranty section of the 
owner’s manual.  The warranty section is found in the rear of the owner’s manual. 

 

Summary of Contents for B009RS

























Reviews: