![background image](http://html.mh-extra.com/html/bomann/ek-6022-cb/ek-6022-cb_instruction-manual_2785748021.webp)
EK6022CB_IM
02.08.18
21
Operation
CAUTION:
Do not switch on the appliance until it has been properly
installed!
NOTE:
• The operation can partly be done via the control panel
of the appliance.
• To set the timer programming, use the remote control.
• Each operating step will be acknowledged by a signal
tone.
• When pressing a wrong button, you will hear two short
beeps.
• After switching on the appliance, the display behind the
glass front becomes visible. For a better ambience, the
display will switch off approx. 20 seconds after each
operation. Press any button to reveal the display again.
Switching on the Appliance
Set the power switch to position
I
. The appliance is in
Standby
. The symbol lights up in the display.
Basic Setting of the Appliance
After switching on the appliance via the power switch, it will
be in the following basic setting:
-
Weekday =
SUN
(Sunday)
-
Display of the current room temperature
-
Time =
-
Intensity of the flames
= high
-
Lighting BACKLIGHT = off
-
Base temperature for heating =
-
Heating = off
-
Timer = off
NOTE:
• Even in the event of a power failure, the appliance is
reset to this basic setting.
• For safety reasons, the appliance will always start
without heating.
Close Operation of the Appliance
• You can switch on the appliance on the control panel by
briefly pressing the
I
/
O
button. The basic setting of the
appliance will become visible in the display.
• If you want to change the intensity of the flames, press
the
I
/
O
button for more than 3 seconds.
• You may turn on the lighting by pressing the
BACKLIGHT
button. Pressing this button repeatedly, will change the
colours. There are 7 different colour variants.
• Press the
POWER
button once to activate the heating
power for 1000 W. Press the
POWER
button a second
time to activate the heating power for 2000 W. Pressing
the button a third time will switch off the heating.
The control lamps beside the button are displaying the
respective status.
NOTE:
The heater and the fan will not be switched on by the
appliance until the room temperature is lower than the
base temperature for the heater (see basic setting).
You can increase the base temperature for the heating
via the remote control.
Operate of the Appliance from the Distance
1. Switch the appliance on by pressing the
ON / OFF
button
on the remote control. The basic setting of the appliance
will become visible in the display.
2. Press the or button to set the base temperature for
the heater. Possible temperature range: Between 15 °C
and 30 °C. Note that the base temperature must be
higher than the current room temperature. If the room
temperature falls below the set base temperature, the
heating will switch on automatically.
3. Use the button
1000 W / 2000 W
to select the heating
power:
Button
Appearance
in the display
Heating power
Press 1 ×
1000 W
Press 2 ×
2000 W
Press 3 ×
off
4. If you want to use the heater’s adaptive start control
function, press the
IC
button. “AUTO” will appear on the
display. Based on the room temperature and the set
temperature the appliance will automatically adjust the
heating power.
5. Press the
BACK-LIGHT
button to select one of 7 colour
variants.
6. Press the
DIMMER
button if you want to change the
intensity of the flames.
Setting the Current Day of the Week and the Time
1. Press the
DATE / TIME
button. The arrow and a
weekday will be flashing. Use the or button to
select a weekday. Press the
DATE / TIME
button again
to confirm the weekday.
2. The hour display starts flashing. Use the or button
to set the current hour. Press the
DATE / TIME
button
again to confirm the hour.
3. The minute display starts flashing. Use the or
button to set the current minute.
4. Press the
OK
button to exit the menu.