There must be a safety distance between the hotplate of the
extractor hood:
The distance
The distance
The distance
The distance must be
must be
must be
must be between 60
between 60
between 60
between 60 ––––
installation instructions for the gas cooker spe
eration.
Selecting the fume outlet
Selecting the fume outlet
Selecting the fume outlet
Selecting the fume outlet
You can operate the extractor hood as described below
A: Extraction mode
To do this, the lever that is located on the motor fan unit
Set the connection piece for the extraction mode
Read the instructions that we give you in "Assembly
Extraction mode
Extraction mode
Extraction mode
Extraction mode
WARNING:
WARNING:
WARNING:
WARNING:
•
The extracted air may not be vented into a flue which is used for the waste gas
from appliances which are
•
When venting the extracted air, comply with the regulations of the relevant local
authorities.
The hood has an upper air outlet to vent
•
The extracted air is normally vented
tracted air is vented through the wall
•
If there is a conduit in your kitchen under the wall units the extraction duct can be routed so that the e
tracted air can be vented horizontally through the wall.
Recirculation mode
Recirculation mode
Recirculation mode
Recirculation mode
If you do not have a direct extraction vent to the
without an extraction vent to the outside; the
vated carbon filter mat as described under
must be used.
The activated carbon filter mat is not
online accessories shop,
www.bomann.de
www.bomann.de
www.bomann.de
www.bomann.de
18
Installation
Installation
Installation
Installation
There must be a safety distance between the hotplate of the cooking pot on the hob and the
–––– 75
75
75
75 cm. For gas appliances, the distance must be at least 65 cm.
cm. For gas appliances, the distance must be at least 65 cm.
cm. For gas appliances, the distance must be at least 65 cm.
cm. For gas appliances, the distance must be at least 65 cm.
installation instructions for the gas cooker specify a greater distance, this distance must be taken into consi
as described below in two modes.
B: Recirculation mode
that is located on the motor fan unit is to set in the corresponding posi
for the extraction mode and the cover for the recirculation mode
tructions that we give you in "Assembly" as well.
The extracted air may not be vented into a flue which is used for the waste gas
from appliances which are powered by gas or other fuels.
When venting the extracted air, comply with the regulations of the relevant local
vent cooking odours to the outside.
vented vertically. If there is a suitable loft space above
wall units and the loft floor to the roof ridge.
If there is a conduit in your kitchen under the wall units the extraction duct can be routed so that the e
ed air can be vented horizontally through the wall.
extraction vent to the outside; the hood can also work in
side; the filtered air is released back into the room). In this case, an
scribed under “Installing the activated carbon filter mat
not supplied. You can order the carbon filter mat fr
www.bomann.de
www.bomann.de
www.bomann.de
www.bomann.de
. To order, use the reference number found under “Technical
ing pot on the hob and the bottom part of the
cm. For gas appliances, the distance must be at least 65 cm.
cm. For gas appliances, the distance must be at least 65 cm.
cm. For gas appliances, the distance must be at least 65 cm.
cm. For gas appliances, the distance must be at least 65 cm. If the
ify a greater distance, this distance must be taken into consid-
in the corresponding position.
the cover for the recirculation mode onto the air outlet.
The extracted air may not be vented into a flue which is used for the waste gas
When venting the extracted air, comply with the regulations of the relevant local
above your kitchen, the ex-
If there is a conduit in your kitchen under the wall units the extraction duct can be routed so that the ex-
side; the hood can also work in recirculation mode (i.e.
nto the room). In this case, an acti-
mat for recirculation mode”,
from your dealer or in our
ber found under “Technical Data”.
