manualshive.com logo in svg

Bolondi SW 060-CF.09, Instruction Manual, Page: 6 / 28

Share
Download
Bolondi SW 060-CF.09 Instruction Manual Download Page 6

Read  this  operating  and  maintenance  manually  carefully  before  using  the  head.  Only  by 
following the instructions herein and becoming familiar with the symbols used is it possible 
to obtain conditions of maximum effi  ciency and safety. The contents of this manual are in 
compliance with machine directive 2006/42/CE and subsequent amendments. The Manu-
facturer reserves the right to make any modifi cations without notice and without incurring 
any  sanctions  on  condition  that  the  main  technical  safety  features  are  not  aff ected.  The 
Manufacturer is not responsible for personal injury or material damage resulting from the 
non-observance of the indications that accompany the symbol.

The  symbol  

represents a safety warning.

Failure to follow the instructions given can cause serious personal injury.

N.B.:

For accident prevention purposes the equipment must be fi tted with suitable devices to pre-
vent automatic re-starting when the equipment is powered after a shut-down. The head must 
not be used without these devices. The Manufacturer declines all responsibility in the case 
of improper use of the equipment.

N.B.:

Please  consult  the  chapter  EXPLODED  VIEW  for  all  the  numbers  and  references  in  the 
manual.

(01-000-00-EN)

1)  INTRODUCTION

SW 060-CF.09-MANUAL Rev.00

6

Summary of Contents for SW 060-CF.09





























Reviews:

No comments