manualshive.com logo in svg

Bolondi SW 060-CF.09, Instruction Manual, Page: 5 / 28

Share
Download
Bolondi SW 060-CF.09 Instruction Manual Download Page 5

TERMS OF WARRANTY

1)  The manufacturer guarantees the rotating head to be free of manufacturing or material 
defects.
2)  Warranty: 2 years for EC countries, 1 year for countries outside the EC (valid from date 
of delivery).
3)  The warranty excludes: all parts subject to normal wear, damage due to carelessness 
or improper use.
4)  The validity of the warranty shall be decided indisputably by the manufacturer.
5)  The warranty excludes labour and transport costs, which are always the responsibility 
of the purchaser.
6)  All spare parts replaced under warranty must be returned to the manufacturer, carriage 
paid, within a maximum of 20 days.
7)  The warranty on the fi nished product or its components shall be void if the product is 
tampered with, modifi ed, or has parts manufactured by third parties installed on it without 
prior authorisation from Bolondi.
8)  Competent court: Judicial Authority of the court of Reggio Emilia, Italy

(00C-Garanzia-00-IT)

SW 060-CF.09-MANUAL Rev.00

5

Summary of Contents for SW 060-CF.09





























Reviews:

No comments