manualshive.com logo in svg

Bolin Technology Visca VCC-BL-VNS-07202020, User Manual

Share
Download
Bolin Technology Visca VCC-BL-VNS-07202020 User Manual Download Page 14

14 

 

Firmware Upgrade 

 

Upgrading MCU Firmware 

MCU Firmware can be upgraded by following these steps: 

1.

 

Load the .bin file onto a flash drive (Formatted as 
FAT32), and 

rename

 the file “HD20.bin” 

2.

 

With the camera powered off

, insert the flash 

drive to the USB port on the back panel of the 
camera 

3.

 

Apply power

 to the camera 

 
After power on the converter box, wait for three minutes, 
the new firmware will be upgraded successfully. There is no LED indicator to show the upgrade progresses.  
The verify is the new firmware is upgraded correctly or not, go to the converter web GUI, System, Maintenance to check 
the firmware version.  
 

NOTE: 
The firmware upgrade process is intended to be performed under the supervision of a BOLIN-Authorized 
repair technician. For assistance with this, please contact your authorized BOLIN Technology dealer, installer, 
or integrator. BOLIN Technology Technical Support can also be reached for assistance with this process 
 

Upgrade via IP 

You can upgrade device IP  Firmware via IP. 
How to make Firmware upgrade for IP, please refer to User Manual Part Two. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Visca VCC-BL-VNS-07202020






















Reviews:

No comments

Brands by name

Popular brands

Load more brands