Bolin Technology D20 Series User Manual Download Page 7

Page: 7 / 54

Overview

This user guide is suitable for the following models: D20H & D20S

Features

•

Can be used as Dante AV Encoder or decoder by upgrading firmware

•

HDMI2.0 input for using as an encoder, HDMI2.0 and 12G-SDI (D20S) output using as an decoder

•

Support up to to 4K@60

•

4K 60 4:4:4 video over standard Gigabit Ethernet

•

Ultra-low latency real-time video performance over the network

•

32-bit wide video interface capable of processing code streams 200-800 Mbps

•

HDMI 7.1 embedded audio input

•

Tunable audio delay to facilitate lip-sync control

•

Support unicast and multicast

•

Full support of Dante audio and video protocols

•

Supported by Dante Controller

•

Fully time-aligned routable audio and video streams

•

Visually perfect video using network efficient JPEG2000 codec

•

Fully validated implementation of HDCP 2.3 encryption

•

Complete EDID support

•

Firmware updateable over the network

•

Works with installed 1Gbps network, no need to replace network infrastructure

•

Powered via POE (25W 802.3at PoE+) or DC power (12V 4A) pack

•

Compact, surface/rack-mountable design

Summary of Contents for D20 Series























































Search results

Summary of Contents for D20 Series

Reviews:

Related manuals for D20 Series

Brands by name

Popular brands

Bolin Technology D20 Series, User Manual

Search results

Summary of Contents for D20 Series

Reviews:

Related manuals for D20 Series

Brands by name

Popular brands