background image

 

Intrusion-3

 Indicator Type is also intended to indicate conditions of intrusion alarm partitions. 

As opposite to 

Intrusion

 Indicator Type, troubles are indicated when there are no other conditions. 

Table 1.4.4.

 Performance of the 

“1” – “60”

 LEDs for Indicators of  

Intrusion-3

 Type

 

Partition Condition 

Performance of the “1” – “60” Indicators 

Panic Alarm, Flooding Detected, 

Intrusion Alarm 

Blinks in red with 0.5 s on and 0.5 s off 

Arming Failed 

Blinks in amber with 0.5 s on and 0.5 s off 

Lobby Alarm 

Blinks in red with 0.25 s on and 0.75 s off 

Disarmed 

Lit steady in green 

Arming 

Blinks in green four times per second 

Armed 

Lit steady in red 

Fault 

Blinks in amber with 0.25 s on and 1.75 s off 

Disabled 

Lit steady in amber (under S2000M ver.3.00+) 

Note: 

Intrusion-3

 Indicator Type operates correctly only with S2000M Fire and Alarm Control Panel 

of ver.2.03 or higher. 

Fire

 Indicator Type is also intended to indicate conditions of individual fire partitions (zones). 

General indicators Fire, Fault, and Disabled of modular fire protection equipment are on the S2000M 
panel. 

Table 1.4.5.

 Performance of the 

“1” – “60”

 LEDs for Indicators of 

Fire

 Type

 

Partition Condition 

Performance of the “1” – “60” Indicators 

Fire2 Alarm 

Lit steady with red 

Fire Alarm 

Blinks in red with 0.25 s on and 0.25 s off 

Fire Prealarm 

Blinks in red with 0.25 s on and 1.75 s off 

Fault 

Blinks in amber with 0.25 s on and 1.75 s off 

Arming Failed 

Blinks in amber with 0.5 s on and 0.5 s off 

Arming 

Blinks in green four times per second 

Armed, Restored, Noise Removed, Mains 

Restored, Battery Restored, Output Normal, 

Tamper Restored, PL Normal, 

Charger Normal, Link Restored, 

Output Communication Normal, 

Input Communication Normal, PL1 Com 

Restored, PL2 Com Restored, DC ON, 

Load Normal, Power Restored, Battery 2  

Normal, Unit Communication Normal 

Lit steady with green 

Disabled 

Lit steady with amber 

Note: S2000M Fire and Alarm Control Panel of ver.3.00 or higher shall be in use. 

Fault

 Indicator Type is intended for indicating faults only and is applicable as to intrusion and 

fire detection partitions (zones). 

Table 1.4.6.

 Performance of the 

“1” – “60”

 LEDs for Indicators of 

Fault

 Type 

Partition Condition 

«1” – “60” LEDs Performance 

Fault 

Blinks in amber with 0.25 s on and 1.75 s off 

Disarmed 

Lit steady with amber 

Disabled 

Lit steady with amber 

Summary of Contents for S2000-BKI






















Reviews: