background image

 

RECEIVER OPERATING MODE PROGRAMMING 

1. 

Power off the Receiver and remove the Receiver lid. 

2.

 

Put on the jumper J. 

3.

 

Connect a 12 Vdc power supply to the Receiver. 

4.

 

Power on the Receiver. 

5.

 

Consider the Receiver periodically blinking. The number of flashes in sets (singly, by twos, in trees 
or in fours) denotes the current operating mode number. 

6.

 

To increase the operating mode number press the large Keyfob button. Inversely, to decrement the 
operating mode number press the small Keyfob button. 

7.

 

Power off the Receiver. 

8.

 

Take off the jumper J in order to save the changes. 

ADDITIONAL KEYFOB PROGRAMMING 

1. 

Take off the Receiver lid. 

2.

 

Connect the Receiver to a 12 ± 2 V direct power supply. Power on the Receiver. 

3.

 

Ensure there are no other operating RF transmitters closer than 50 meters. 

4.

 

Shortly (within no more than 2 seconds) press the LEARN button located on the Receiver PC board 
to program a new Keyfob. The Receiver LED shall light up indicating programming mode initiating. 

D

Caution

: Holding the LEARN button for more than 8 seconds will erase the Receiver memory so 

that data about all Keyfobs programmed before will be lost. 
5.

 

Shortly press large or small Keyfob button and ensure the Receiver LED goes off. If the LED has no 
gone off then the RF relationship between Receiver and Keyfob is not created. 

D

Caution

: If the programming Keyfob button is not pressed within 30 second interval, having been 

expired since Receiver programming mode initiating (pressing of the PC board LEARN button), the 
programming mode will be prohibited. To resume the programming procedure return to the step 4. 
6.

 

In case of programming having been successful (the Receiver LED has gone off after pressing a 
Keyfob button) press the Keyfob button once more. 

7.

 

To program another Keyfob (no more than 14 additional ones can be programmed) repeat the steps 
from 4 to 6. 

8.

 

Bring the lid back onto the Receiver base. 

9.

 

Ensure all programmed Keyfobs are capable to operate properly having been located at the ordinary 
places. 

RECEIVER MEMORY CLEARING 

Remove the Receiver lid and keep LEARN button pushed for more than 8 seconds. All Keyfobs data 

having been already registered will be deleted. 

Summary of Contents for EFIR-K











Reviews: