BobsCNC RP9V2 Assembly Instructions Manual Download Page 45

Page: 45 / 45

The parts in the deluxe kit can be purchased separately.

The extruder for the RP9 printer can be found at:

BobsCNC.com

The

NEMA17

stepper motors can be found in many online stores. The

extruder stepper should rated holding torque of

5.5Kg.cm (76 oz-in). Other

stepper motors can be less but could reduce performance. Search for
"

printer stepper motors"

The feedstock drive wheel needs to fit a 5 mm shaft and
knurling bottom diameter of 6 mm. Search online for

"feedstock drive wheel"

The Arduino, Ramps1.4, and A4988 stepper drives (with heat sinks)
are common in online stores.
The power supply should be 12 VDC an rated at 6 to 8 amps. Search
online for

"12 VDC 8 amp power supply"

Other supplies that you will need are:

Build plate can be hardboard, glass, aluminum, etc.

Size is 200 to 215 mm square

Blue painters tape ( or a glue stick) and build plate clips
1.75 mm PLA with 0.05 mm tolerance

Summary of Contents for RP9V2














































Search results

Summary of Contents for RP9V2

Reviews:

Related manuals for RP9V2

Brands by name

Popular brands

BobsCNC RP9V2, Assembly Instructions Manual

Search results

Summary of Contents for RP9V2

Reviews:

Related manuals for RP9V2

Brands by name

Popular brands