BobsCNC RP9 Assembly Instructions Manual Download Page 39 | Manualshive

Page: 39 / 45

background image

39

First print (quick guide)

Initial setup and calibration of the printer will takes some time but once you

understand the parameters you will be able to diagnose printing issues quickly. We have
included some basic steps to get you started.

Connecting the printer

1. Connect the power supply
2. Connect the controller to the computer via USB
3. Open the controller software and connect the printer (250,000 baud rate)

Moving the X, Y, and Z axis

1. Use the software controls to move the X,Y and Z
steppers. make sure the move in the correct
direction. The diagram has arrows showing the
positive axis directions.

If the motors move in the incorrect

direction, it can be changed with a firmware setting
or turning the stepper motor connectors 180
degrees. The power must be removed before stepper
motor connectors can be removed to avoid damage
to the controller board.

Loading the 1.75 mm filament

«
...
37
38
39
40
41
...
»

Summary of Contents for RP9














































Reviews:

No comments

Related manuals for RP9

Brand: Qilive Pages: 398

WORKCENTER 5222

Brand: Xerox Pages: 28

VersaLink C7000

Brand: Xerox Pages: 2

WorkCentre 6505

Brand: Xerox Pages: 4

Brand: Xerox Pages: 4

Brand: Xerox Pages: 5

Brand: Xerox Pages: 8

WORKCENTRE 5735

Brand: Xerox Pages: 18

Brand: Xerox Pages: 2

Brand: Xerox Pages: 116

Brand: Xerox Pages: 3

Brand: Xerox Pages: 55

wematter Atmosphere

Brand: 3D Systems Pages: 11

Brand: Rena Pages: 59

VarioPrint 6180

Brand: Oce Pages: 306

Brand: Ricoh Pages: 44

Brand: Oki Pages: 8

Brand: Xerox Pages: 244

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands