background image

BNR6400 Tech Manual.indd • 07242013

Page | 5

The switch position enables you to work at high or low 

speeds. The gear switch position should only be changed 

when the unit is stopped in order to prevent the gearing 

from being damaged.

1st gear - Upper position

2nd gear- Lower position

CARE AND MAINTENANCE

•  Remove the plug from the socket before making any 

adjustment, servicing or maintenance.

•  Your power tool requires no additional lubrication or 

maintenance. Always store your power tool in a dry-

place.

•  If the electric cord is damaged, it must be replaced by 

the manufacturer, service agent or similarly qualified 

persons in order to avoid a hazard.

CLEANING

•  Keep the safety devices, ventilation slots and motor 

housing as free of dirt and dust as possible. 

•  Clean the unit by rubbing it with a clean cloth or blow 

it clean using low-pressure compressed air.

•  We recommend that you always clean the unit imme-

diately after using it.

•  Clean the unit regularly by rubbing it with a damp cloth 

and a little soft soap. Do not use cleaners or solvents 

--these will attack the plastic parts in the unit. You 

must also ensure that water cannot get into the inside 

of the unit.

• 

CARBON BRUSHES

If excessive sparking occurs you must have the carbon 

brushes checked by a qualified electrician.

Attention! Changing the brushes should be done by a quali-

fied electrician.

MAINTENANCE

There are no parts fitted inside the unit that require main-

tenance.

CORRECTIVE ACTION IN CASE OF FAILURE

The operating switch is switched on, but the motor is 

not working.

•  Wires in the electric plug or in the socket are loose. 

Have socket and plug checked or repaired or replaced.

•  The switch is faulty. Have the switch replaced.

The operating switch is switched on, but unusual nois-

es can be heard, the motor is not working or only very 

slowly.

•  Switch contact has failed. Have the switch replaced.

•  Component jammed. Have the electric tool checked or 

repaired.

•  Too much thrust, as a result the motor is dragging. Use 

less thrust during the task.

Motor gets hot.

•  Foreign substances have got inside the motor. Have the 

foreign substances removed.

•  Lack of or contaminated lubrication grease. Have lu-

bricating grease applied or replaced.

•  Pressure too high. Use less thrust during the task

Frequent or strong sparks on the commutator.

•  Short circuit on the armature. Have the armature re-

placed.

•  Carbon brushes worn out or jammed. Have the carbon 

brushes checked.

•  Rough running of the commutator. Have the surface of 

the commutator cleaned or ground.

For your own safety, never remove parts or accessories of 

the electric tool during operation, In case of fault or

damage have the electric tool repaired only by a specialist 

workshop or by the manufacturer.

•  Variable speed adjustment with a lock-on 

feature.

•  Two-speed gear box.

•  Powerful high torque motor.

•  Soft-start and constant speed control.

•  Ergonomically designed handle with soft 

grip design.

•  Double insulated.

•  12’ power cord.

•  Standard M14 paddle  

connection.

•  BNRA0315 1/2” Chuck

•  Includes general purpose mixing paddle  

(2’x 6-1/2”).

The BNR6400 

Hand Held Power Mixer

Summary of Contents for BNR6400









Reviews: