2. INTRODUCTION & SPECIFICATION
This heater produces a totally dry heat, no condensation, no gas, no fumes. It reaches maximum heat output within a minute from being turned on. It
is quick and easy to install reducing installation costs. Used with the CS-1 controller it can provide low / high heat or fan only settings.
Model
860T
Power
6000W
Input supply
220-240V
Dimensions (W x D x H)
1105 x 108 x 225mm
Weight
14kg
Recommended Mounting Height
1.8 - 3.0M
Safety Distance from Heater
1.5M
Optional Controller Model Number
CS-1
3. LOCATION OF HEATER
When used as a space heater it should be mounted at a height of 1.8
– 3m above floor level and a minimum of 300mm from the ceiling and adjacent
walls.
We do not recommend the 860T be used as an overdoor heater on an external door as the built-in thermostat can be unnecessarily activated when
the outside door is opened.
When used above an internal doorway, the heater can be wall or ceiling mounted at a height of 1.8
– 3m above floor level and a minimum of 300mm
from adjacent walls.
4. MOUNTING INSTALLATION
IMPORTANT!
DO NOT mount heater directly below the socket outlet.
IMPORTANT!
Ensure that the mounting surface / ceiling supports are capable of taking the weight of the heater.
IMPORTANT!
Do not allow any object to come closer than 1.5m to the heater outlet.
IMPORTANT!
Always mount the heater horizontal mounting at any other angle will reduce the heater
’s life and invalidate the guarantee.
IMPORTANT!
The air intake and discharge areas must be kept completely clear for a minimum of 1.5m from the front of the heater.
4.1
MOUNTING KIT
The mounting kit supplied with each heater consists of the following items.
1 x Fixing Plate (approximately the same length as the heater), 2 x Small Side Brackets, 2 x Large Side Brackets, 2 x Plastic Domes
4 x M2.9 Self Tapping Screws, 6 x M4 x 10mm Long Pozi Drive Screws and 2 x M4 Lock washers.
4.2
WALL MOUNTING ABOVE AN INTERNAL DOORWAY
Attach the two Small Side brackets to the heater using the Plastic Domes and M2.9 Screws. Make sure both open slots are facing downwards
and the brackets face towards the back of the heater (see Pic 1).
Securely attach the Fixing Plate to the wall. Partially insert M4 screws into the outer two holes in each end of the bracket. Make sure the screw
goes all the way through and the thread is just showing the other side (see Pic 2). The heater with its two end brackets should now be slotted
onto the fixing bracket (see Pic 3). Now tighten up the four end screws and add an additional M4 centre screw and lock washer into the centre
hole at each end of the fixing bracket (see Pic 4). UNDER NO CIRCUMSTANCES MUST THE HEATER BE TURNED ON IF THESE TWO
CENTRE SCREWS AND LOCK WASHERS ARE NOT PRESENT OR TIGHTENED UP.
4.3
CEILING MOUNTING ABOVE AN INTERNAL DOORWAY
You can either use M8 drop rods in the two threaded holes in the top of the heater (drop rods not supplied) or
mount directly to the ceiling using the supplied brackets. If mounting using the supplied brackets use the method
(section 4.2) above with the exception that you use the Large Side Brackets and they must face upwards (see
Pic5). Do not switch on unless the 2 centre screws and lock washers are fitted to the side brackets and tightened.
4.4
WALL MOUNTING FOR SPACE HEATING
The mounting method is the same as described above (section 4.2) above with the
exception that you use the Large Side Brackets and they must face backwards (see
Pic 6). Do not switch on unless the 2 centre screws and lock washers are fitted to
the side brackets and tightened. The angle of the heater can be adjusted by
releasing the Plastic Domes by unscrewing the self-tapping screws a half turn twist
the heater to required angle then tighten up the screws. The heater may only be
used between 90° (horizontal) and 180° (vertically downwards).
Pic 1
Pic 2
Pic 3
Pic 4
Pic 5
Lock Washer
Pic 6
CS-1 Controller
(Optional Extra)
