BMW Z8 Owner'S Manual Download Page 77

Page: 77 / 175

Index

Data

Technology

Repairs

Car care

Controls

Overview

Heating and ventilation/Air conditioner

Seat heating

Rapid heating

1. Set the rotary control for the air

supply to position 3

2. Turn the rotary temperature control

completely to the right

3. Rotary control for air distribution in

position

4. Select incoming-air mode.

520de045

Heating

When the windows are free of ice and
condensation, we recommend the fol-
lowing settings:

1. Set the rotary control for the air

supply to position 2

2. Use the rotary temperature control to

select an interior temperature com-
fortable for you

3. Rotary control for air distribution in

position .

520de047

The seat cushion and backrest can
be heated when the ignition key is in
position 2.

By repeatedly pressing the button, you
can select one of three different opera-
tion modes:

Two indicator lamps on: heating at
high temperature

One indicator lamp on: heating at low
temperature

Indicator lamps off: seat heating
deactivated.

520de048

Online Edition for Part No. 01 41 0 156 878 - © 06/02 BMW AG

Summary of Contents for Z8
















































































































































































Search results

Summary of Contents for Z8

Reviews:

BMW Z8, Owner'S Manual, Page: 77 / 175

Search results

Summary of Contents for Z8

Reviews: