BMW Z8 Owner'S Manual Download Page 34

Page: 34 / 175

Opening and closing – from the outside

To unlock the vehicle

Press button 1.

Press the button once to unlock the
driver's door only; press it a second
time to unlock the passenger door, the
luggage compartment lid, the fuel filler
door, the glove compartment, and the
cellular phone holder.

If necessary, you can open the fuel filler
door by pressing the button inside the
vehicle, refer to page

Convenience opening mode

Press and hold button 1. The windows
are then opened.

520de143

To lock and secure

Press button 2.

You can have a signal set as an
acknowledgement that the vehicle

is properly locked.

520de145

To deactivate the tilt alarm sensor
and interior motion sensor

Press button 2 again immediately after
locking.
For additional information: page

To switch on the interior lamps

With the vehicle locked, press button 2.

520de145

Online Edition for Part No. 01 41 0 156 878 - © 06/02 BMW AG

Summary of Contents for Z8
















































































































































































Search results

Summary of Contents for Z8

Reviews:

BMW Z8, Owner'S Manual, Page: 34 / 175

Search results

Summary of Contents for Z8

Reviews: