BMW F 650 GS Manual Download Page 69

Page: 69 / 88

Techn

ica

l d

F 650 GS

F 650 Dakar

Wheels and tires

Spoked wheel

You can obtain detailed information
on approved tire sizes and makes
from your authorized BMW motor-
cycle retailer or by visiting
www.bmw-motorrad.com on the
Internet

Front wheel

Size and designation

2.50“ x 19“ MT

1.6" x 21"

Tire size and designation

100/90-19

90/90-21

Rear wheel

Size and designation

3.00“ x 17“ MT

Tire size and designation

130/80 R 17

130/80-17

Tire pressures (tires cold)

One-up

Front

27.56 psi (1.9 bar)

Rear

30.46 psi (2.1 bar)

Fully loaded

Front

30.46 psi (2.1 bar)

Rear

33.36 psi (2.3 bar)

Recommended minimum tire tread depth

Front wheel

0.08 in (2 mm)

Rear wheel

0.12 in (3 mm)

Comply with local legal requirements concerning minimum
tread depth.

Frame and suspension

20r13bku4.book Seite 67 Montag, 29. September 2003 12:33 12

Summary of Contents for F 650 GS

























































































Search results

Summary of Contents for F 650 GS

Reviews:

Related manuals for F 650 GS

Brands by name

Popular brands

BMW F 650 GS, Manual

Search results

Summary of Contents for F 650 GS

Reviews:

Related manuals for F 650 GS

Brands by name

Popular brands