BMT 932 Manual Download | Manualshive

Page: 50 / 52

background image

OZONE MONITOR BMT 932 Manual, Rev. 02/2021

50

Warning:

This product relies on the building's installation for short-circuit (overcurrent) protec-

tion. Ensure that a fuse or circuit breaker no larger than 15 A at 120 VAC (10 A at 240 VAC) is
used on the phase conductor.

Warning:

Disconnect electrical power before opening the cabinet door.

Précaution

: Couper l'alimentation avant d'ouvrier la porte d'analyseur.

Signal contacts (Connector "Output & Control") are as described on page 15. A splash-proof
connector for connection of the supplied serial cable is provided.

The BMT 932 C can be ordered with the option 932C-HAR. This provides a relay which can
switch an alarm horn in case of a High Concentration Alarm. Connection is made through an
additional splash-proof feed-through to the two pole connector on the PCB labeled "Horn". Ca-
ble diameter shall be 6.5 to 10 mm.

Warning:

The equipment connected to the option 932C-HAR shall be fused at 4 A.

Précaution

: Assurer la protection de l’équipement connecté au option 932C-HAR avec une fusible pour 4A.

C4

Operation

The operation of the BMT 932 C is the same as of the standard BMT 932.

For further description of the functions and properties of the cabinet version please refer to the
main part of this manual.

«
...
48
49
50
51
52
»

Summary of Contents for 932





















































Reviews:

No comments

Related manuals for 932

Brand: Acer Pages: 13

Brand: Acer Pages: 2

Brand: Acer Pages: 2

Brand: Acer Pages: 20

Brand: Daewoo Pages: 19

Brand: Daewoo Pages: 12

Brand: Daewoo Pages: 36

Brand: Daewoo Pages: 70

Brand: I-Tech Pages: 16

Tel-O-Graph GSM

Brand: I.E.M. Pages: 47

Brand: Alecto Pages: 16

Brand: urmet domus Pages: 40

Brand: FDS Pages: 25

Brand: VTech Pages: 18

Brand: Ditel Pages: 2

Brand: SRLine Pages: 26

BP B3 Comfort PC

Brand: Microlife Pages: 90

Brand: Hitachi Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands