Minimum Temperature:
The unit records the minimum temperature
measured by the sensor. To reset the minimum temperature, press
the MENU button to display the first menu item. Use the UP and
DOWN arrow buttons to scroll through and find “Minimum Temp” on
the LCD screen. To reset, press the ENTER button twice after the
value is displayed.
Maximum Temperature:
The unit records the maximum temperature
measured by the sensor. To reset the maximum temperature, press
the MENU button to display the first menu item. Use the UP and
DOWN arrow buttons to scroll through and find “Maximum Temp”
on the LCD screen. To reset, press the ENTER button twice after the
value is displayed.
Control Mode:
The unit will operate to increase or decrease the tem-
perature depending on the device connected to the unit. To change
the Control Mode, press the MENU button to display the first menu
item. Use the UP and DOWN arrow buttons to scroll through and find
“Control Mode” on the LCD screen. To change the setting, press the
ENTER button. The current setting will be highlighted to indicate the
setting can be changed. Use the UP and DOWN arrow buttons to
change the setting. Press the ENTER button a second time to accept
the new setting and store it in memory.
Temperature Display:
The unit will display the temperature in °F or
°C. To change the Temperature Display, press the MENU button to
display the first menu item. Use the UP and DOWN arrow buttons
to scroll through and find “Set Temp Display” on the LCD screen. To
change the setting, press the ENTER button. The current setting will
be highlighted to indicate the setting can be changed. Use the UP and
DOWN arrow buttons to change the setting. Press the ENTER button
a second time to accept the new setting and store it in memory.
Troubleshooting
The LCD screen is blinking and showing an error
message.
All detected errors will cause the unit to go into “safe mode.” It will shut
down the connected device and display one of the following errors:
Temp Sensor
(problem with sensor)
Overload
(current draw exceeds 10A)
Holding the ENTER button for 3 seconds will reset any error except
for OVERLOAD. In this case, disconnect the unit from the electrical
supply to reset the error. It may be necessary to reduce the size of the
connected equipment (if it exceeds a 10A draw) to prevent the OVER-
LOAD error from reoccurring.
See warranty procedure information if you reset the unit and the error
code continues to appear.
How can I calibrate the temperature sensor?
The sensor does not require any calibration.
The unit is turning on and off at the wrong temperatures.
Make sure you have selected the correct control mode for the device
connected to the unit.
Limited 3-Year Warranty Terms
Sunleaves Garden Products warrants that the Blueprint Digital Day/Night Temperature Controller will remain free from
appearance of defects in workmanship and materials for 3 years from date of original retail purchase. This warranty is
subject to the following limitations: (a) manufacturer’s liability is limited to the replacement or repair of the unit, as decided
by the manufacturer; (b) a defective unit must be returned, prepaid, with proof of purchase to the point of purchase or as
instructed below; and (c) this warranty does not apply to defects resulting from the alteration, abuse, accidental damage,
unauthorized repair or misuse of the unit. This warranty is given in lieu of all other warranties, guarantees and conditions
on manufacturer’s part, and the manufacturer shall have no tortious or other liability in respect to this Blueprint Digital
Day/Night Temperature Controller.
Blueprint Digital Day/Night Temperature Controller Warranty Is Void If:
• NOT ACCOMPANIED BY THE ORIGINAL PROOF OF PURCHASE.
• BLUEPRINT DIGITAL DAY/NIGHT TEMPERATURE CONTROLLER HAS BEEN USED IN A NONSTANDARD WAY, INCLUDING GENERAL MISUSE
AND OUTDOOR USE.
• BLUEPRINT DIGITAL DAY/NIGHT TEMPERATURE CONTROLLER HAS BEEN DAMAGED AS A RESULT OF ACCIDENT, IMPROPER
INSTALLATION, ALTERATION, OR FIRE, FLOOD OR OTHER NATURAL DISASTER.
Blueprint 3-Year Limited Warranty
All Blueprint Digital Day/Night Temperature Controllers are protected against manufacturer defect by a limited
3-year manufacturer’s warranty.
Sunleaves Product Warranty Claims
To obtain warranty service in the event that your product fails to operate, return the product to the place of purchase. Often the retailer will be able
to examine the product in closer detail, determine the problem and even fix the product on site.
For technical support and warranty information, call our toll-free number at 888-464-9676
or email: [email protected].
7854 North State Road 37
Bloomington, IN 47404
rev:112013
