manualshive.com logo in svg

Blue Sea Systems Battery LINK 7606, User Manual

Share
Download
Blue Sea Systems Battery LINK 7606 User Manual Download Page 9

Specifications are subject to change. See bluesea.com/products/7606 for current information.

8

FULL INSTALLATION DIAGRAM

start

run

accessory

off

START KEY SWITCH

NEGA

TIVE

STUD

POSITIV

E

STUD

S

OPTIONAL

START ISOLATION

(SI) WIRE

OPTIONAL

BATTERY 

TEMPERATURE

SENSOR

Legend

Ground

OPTIONAL 

REMOTE 

INDICATOR

Optional

DC Negative

DC Positive

AC INPUT

BatteryLink™ Charger 20A

MULTISTAGE CHARGER

INTEGRATED ACR

2A FUSE  

16 AWG 

(1.5mm²)

FUSE*

2A FUSE  

16 AWG 

(1.5mm²)

FUSE*

FUSE*

NEGATIVE 

BUS BAR

ACCESSORIES

AUXILIARY

BATTERY

START

BATTERY

2A FUSE  

16 AWG 

(1.5mm²)

FUSE**

7606

AC

AC Connections

Line: Brown
Neutral: Blue
Ground: Green/Yellow

DC SAFETY

GROUND***

OPTIONAL

COMBINE

SWITCH

(sold separately)

YELLOW WIRE

RED WIRE

ENGINE

*   See Wire Size and Fuse Rating Table, page 5.
**  Wire size and fuse rating based on house loads. For more information, use the Circuit Wizard at circuitwizard.bluesea.com.
*** DC safety ground wire must be no more than one nominal wire size smaller than the positive battery wires. If the rating of the circuit  
 

protection used in the positive battery wires is greater than 135% of the ampacity of the smaller proposed DC safety ground wire,  

 

then the DC safety ground wire must be the same size as the positive battery wires.

Summary of Contents for Battery LINK 7606













Reviews:

No comments

Brands by name

Popular brands

Load more brands